EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Effect of margin designs and loading conditions on the stress distribution of endocrowns: a finite element analysis

Baijin Zeng, Bin Luo, Jiangqi Hu, Dan Meng, Jiebing Zhang, Xu Cao, Qingsong Jiang

BMC Oral Health · 2024

DOI: 10.1186/s12903-024-04422-3 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift BMC Oral Health, 2024. Verfasst von Baijin Zeng und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Beijing Stomatological Hospital, School of Stomatology, Capital Medical University, No. 4 Tiantanxili, Dongcheng Distri…. Hauptthemen laut MEDLINE: Finite Element Analysis, Stress, Mechanical, Dental Stress Analysis. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Young Scientist Program of Beijing Stomatological Hospital, Capital Medical University, Capital' s Funds for Health Improvement and Research, Capital’ s Funds for Health Improvement and Research.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Margin designs and loading conditions can impact the mechanical characteristics and survival of endocrowns. Analyzing the stress distribution of endocrowns with various margin designs and loading conditions can provide evidence for their clinical application.

Methods

Three finite element analysis models were established based on the margin designs: endocrown with a butt-joint type margin (E0), endocrown with a 90° shoulder (E90), and endocrown with a 135° shoulder (E135). The E0 group involved lowering the occlusal surface and preparing the pulp chamber. The E90 group created a 90° shoulder on the margin of model E0, measuring 1.5 mm high and 1 mm wide. The E135 group featured a 135° shoulder. The solids of the models were in fixed contact with each other, and the materials of tooth tissue and restoration were uniform, continuous, isotropic linear elasticity. Nine static loads were applied, with a total load of 225 N, and the maximum von Mises stresses and stress distribution were calculated for teeth and endocrowns with different margin designs.

Results

Compared the stresses of different models under the same loading condition. In endocrowns, when the loading points were concentrated on the buccal side, the maximum von Mises stresses were E0 = E90 = E135, and when there was a lingual loading, they were E0 < E90 = E135. In enamel, the maximum von Mises stresses under all loading conditions were E0 > E90 > E135. In dentin, the maximum von Mises stresses of the three models were basically similar except for load2, load5 and load9. Compare the stresses of the same model under different loading conditions. In endocrowns, stresses were higher when lingual loading was present. In enamel and dentin, stresses were higher when loaded obliquely or unevenly. The stresses in the endocrowns were concentrated in the loading area. In enamel, stress concentration occurred at the cementoenamel junction. In particular, E90 and E135 also experienced stress concentration at the shoulder. In dentin, the stresses were mainly concentrated in the upper section of the tooth root.

Conclusion

Stress distribution is similar among the three margin designs of endocrowns, but the shoulder-type designs, especially the 135° shoulder, exhibit reduced stress concentration.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Finite Element AnalysisStress, MechanicalDental Stress AnalysisHumansDental Prosthesis DesignCrownsBiomechanical PhenomenaDentin

Stichwörter der Autor:innen

EndocrownFinite element analysisLoading conditionMargin designThe maximum von Mises stress

Autor:innen und Institutionen

  • Department of Prosthodontics, Beijing Stomatological Hospital, School of Stomatology, Capital Medical University, No. 4 Tiantanxili, Dongcheng District, Beijing, 100050, China.
  • Department of Prosthodontics, Beijing Stomatological Hospital, School of Stomatology, Capital Medical University, No. 4 Tiantanxili, Dongcheng District, Beijing, 100050, China. dentistcao@mail.ccmu.edu.cn.
  • Department of Prosthodontics, Beijing Stomatological Hospital, School of Stomatology, Capital Medical University, No. 4 Tiantanxili, Dongcheng District, Beijing, 100050, China. qsjiang@ccmu.edu.cn.

Förderung

  • Young Scientist Program of Beijing Stomatological Hospital, Capital Medical University
  • Capital' s Funds for Health Improvement and Research
  • Capital’ s Funds for Health Improvement and Research

Zitieren

APA

Zeng, B., Luo, B., Hu, J., Meng, D., Zhang, J., Cao, X., & Jiang, Q. (2024). Effect of margin designs and loading conditions on the stress distribution of endocrowns: a finite element analysis. BMC Oral Health. https://doi.org/10.1186/s12903-024-04422-3

Vancouver

Zeng B, Luo B, Hu J, Meng D, Zhang J, Cao X, et al. Effect of margin designs and loading conditions on the stress distribution of endocrowns: a finite element analysis. BMC Oral Health. 2024. doi:10.1186/s12903-024-04422-3

BibTeX
@article{Zeng2024,
  author = {Zeng, Baijin and Luo, Bin and Hu, Jiangqi and Meng, Dan and Zhang, Jiebing and Cao, Xu and Jiang, Qingsong},
  title = {Effect of margin designs and loading conditions on the stress distribution of endocrowns: a finite element analysis},
  journal = {BMC Oral Health},
  year = {2024},
  doi = {10.1186/s12903-024-04422-3}
}
Kostenlos starten →