EUVIMEDEUVIMED entdecken
Crossref

Investigation of tool pass influence on graphene-reinforced Al6061 composites processed by FSP for improved performance

Binit Kumar, Leeladhar Nagdeve, Harish Kumar

Journal of Reinforced Plastics and Composites · 19.02.2026

DOI: 10.1177/07316844261428796 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Reinforced Plastics and Composites, online erschienen am 19.02.2026. Verfasst von Binit Kumar und 2 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Al6061 alloy is effectively used in the construction, aerospace, and automotive industries due to its high strength-to-weight ratio, but it exhibits inferior wear performance. A possible method for improving the tribological characteristics of Al6061 alloy through microstructural alteration is the friction stir process (FSP). The current article correlates the outcomes of the number of passes of the tool with mechanical and tribological properties. Furthermore, carbon particles such as graphene have been reinforced in Al6061 metal matrix so as to understand their impact on mechanical and wear properties. Over two passes of friction stir process, graphene-reinforced metal matrix composite (MMC) reveals improved performance over the unprocessed sample, leading to its effectiveness towards tribology. Macrograph observation revealed the flow of plasticized material from the retreating side to the advancing side. Retention of graphene particles inside the stir zone was confirmed by the appearance of the G-band and 2D-band through Raman spectroscopy. Microhardness observation revealed a peak hardness of 138.93 ± 1.29 HV for the graphene-reinforced metal matrix as compared with the untreated sample 61.57 ± 0.03 HV. A significant reduction in wear volume (from O ∼ 0.23 ± 0.006 × 10 −3 mm 3 to T/G-2 ∼ 0.058 ± 0.003 × 10 −3 mm 3 ) and coefficient of friction (from O ∼ 0.71 ± 0.014 to T/G-2 ∼ 0.29 ± 0.005) was observed in the case of graphene-reinforced MMC for two passes of the tool, attributed to its self-lubricating behavior. Furthermore, a decrement in crystallite size was observed for graphene-reinforced MMC (T/G-2 ∼ 27 ± 3 nm) as compared with untreated material (O ∼ 48 ± 3 nm). Additionally, oxide layer formation on the counter surface contributed to improved tribological performance, highlighting graphene’s effectiveness in enhancing wear resistance and frictional characteristics.

Zitieren

APA

Kumar, B., Nagdeve, L., & Kumar, H. (2026). Investigation of tool pass influence on graphene-reinforced Al6061 composites processed by FSP for improved performance. Journal of Reinforced Plastics and Composites. https://doi.org/10.1177/07316844261428796

Vancouver

Kumar B, Nagdeve L, Kumar H. Investigation of tool pass influence on graphene-reinforced Al6061 composites processed by FSP for improved performance. Journal of Reinforced Plastics and Composites. 2026. doi:10.1177/07316844261428796

BibTeX
@article{Kumar2026,
  author = {Kumar, Binit and Nagdeve, Leeladhar and Kumar, Harish},
  title = {Investigation of tool pass influence on graphene-reinforced Al6061 composites processed by FSP for improved performance},
  journal = {Journal of Reinforced Plastics and Composites},
  year = {2026},
  doi = {10.1177/07316844261428796}
}
Kostenlos starten →