3D Printing and Optimization of Biocompatible and Hydrophilic PEGDA‐HEMA Lattice for Enhanced RhB Dye Removal From Aqueous Solution
International Journal of Polymer Science · 2024-01 · 2024 (1)
DOI: 10.1155/2024/6633503 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Polymer Science, online erschienen am 07.11.2024. Verfasst von Ting Sheng Ng und 6 weiteren Autor:innen. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 88 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Higher Education, Malaysia.
Abstract (Originalsprache)
A formulated photocurable poly(ethylene glycol) diacrylate (PEGDA) and 2‐hydroxylethyl methacrylate (HEMA) polymer matrix (PEGDA:HEMA) was developed for constructing an adsorptive 3D cubic monolith using masked stereolithography (MSLA) 3D‐printing technique. A pure PEGDA formulation served as a control in comparative studies. Additionally, two structural designs (solid cube and cubic lattice) were also quantitatively compared to determine the adsorption performance for Rhodamine B (RhB) dye removal. Results indicated that the cubic lattice formulated with hydrophilic PEGDA:HEMA ( θ ~47.20°) was more effective at removing RhB dye. Additionally, the preliminary study identified pH 9 as the optimal level for RhB dye removal using 3D cubic monolith for both formulations. A Taguchi orthogonal array of L9 (3 3 ) was used to concurrently vary three parameters: adsorbent dosage (0.65 ± 0.02 g per cubic lattice), operating temperature (30°C, 40°C, and 50°C), and initial RhB concentration (20, 60, and 100 ppm). The highest mean of the signal‐to‐noise (S/N) ratio was chosen to obtain the highest adsorption performance. The removal efficiency (R%) of RhB dye ranged from 44.48% to 94.86%, and the adsorption capacity (K) ranged from 0.59 to 3.73 (mg/g) after 5 h. Seven adsorption isotherms and five adsorption kinetics modelling were performed. Adsorption isotherm data fitted well with the Redlich–Peterson model for both linear ( R 2 = 0.998) and nonlinear ( R 2 = 1). Besides that, the pseudo‐second‐order model (PSO) accurately described adsorption kinetics ( R 2 = 0.995). The separation factor ( R L ) confirmed favourable adsorption (0 < R L < 1). Thermodynamic parameters indicated that the adsorption process was endothermic and at higher temperatures, entropy increased. Also, the 3D–printed PEGDA:HEMA cubic lattice exhibited good mechanical stability. Furthermore, the 3D PEGA: HEMA lattice has the ability to be used in several adsorption cycles of degrading RhB dye. Ultimately, the present work demonstrates the viability of 3D printing photocurable PEGDA:HEMA resin and utilizes statistical tools to optimize process parameters, enhancing predictability for wastewater management.
Förderung
- Ministry of Higher Education, Malaysia
Zitieren
APA
Ng, T. S., Norman, A., Yusoff, N. H. M., Chong, C. H., Cheah, K. H., Yap, T. C., & Wong, V. (2024). 3D Printing and Optimization of Biocompatible and Hydrophilic PEGDA‐HEMA Lattice for Enhanced RhB Dye Removal From Aqueous Solution. International Journal of Polymer Science, 2024(1). https://doi.org/10.1155/2024/6633503
Vancouver
Ng TS, Norman A, Yusoff NHM, Chong CH, Cheah KH, Yap TC, et al. 3D Printing and Optimization of Biocompatible and Hydrophilic PEGDA‐HEMA Lattice for Enhanced RhB Dye Removal From Aqueous Solution. International Journal of Polymer Science. 2024;2024(1). doi:10.1155/2024/6633503
BibTeX
@article{Ng2024,
author = {Ng, Ting Sheng and Norman, Ashreen and Yusoff, Nurul Husna Mohd and Chong, Chien Hwa and Cheah, Kean How and Yap, Tze Chuen and Wong, Voon-Loong},
title = {3D Printing and Optimization of Biocompatible and Hydrophilic PEGDA‐HEMA Lattice for Enhanced RhB Dye Removal From Aqueous Solution},
journal = {International Journal of Polymer Science},
year = {2024},
volume = {2024},
number = {1},
doi = {10.1155/2024/6633503}
}
EUVIMED