A Novel Rolling-Assisted, Extrusion-Based Dry 3D Printing Process for High-Loading Lithium-Ion Battery Electrodes
ECS Meeting Abstracts · 07.07.2026 · MA2026-01 (2) · 154-154
DOI: 10.1149/ma2026-012154mtgabs ↗Kurz gefasst
Fachartikel in der Zeitschrift ECS Meeting Abstracts, erschienen am 07.07.2026. Verfasst von Yihao Shen und 3 weiteren Autor:innen.
Abstract (Originalsprache)
Conventional slurry-based manufacturing of lithium-ion battery (LIB) electrodes relies heavily on toxic and expensive organic solvents such as N-methyl-2-pyrrolidone (NMP). The slurry process requires extensive mixing, long time drying, and complex solvent-recovery infrastructure, resulting in high energy consumption and significant environmental impact. Slurry-based electrodes often suffer from binder migration, particle agglomeration, and non-uniform pore distribution during drying, which become more severe at high solid content and make it difficult to achieve industrial-level high areal loading or maintain efficient ion-transport pathways. As global demand for LIBs continues to expand, the need for a solvent-free, energy-efficient, and scalable manufacturing route has become increasingly urgent. To address these challenges, we develop a Rolling-assisted, Extrusion-based Dry (RED) 3D printing process as a sustainable alternative to conventional slurry coating. In this method, a fully dry composite filament consisting of active material (AM), carbon black (CB), and polyvinylidene fluoride (PVDF) is first produced using a conventional filament extrusion machine, without any solvent. The extruded filament is then used as the feedstock for 3D printing, where it forms parallel filament tracks on the Al foil that act as a supporting layer for the electrode. During printing, a dry powder blend consisting of AM, CB, and PVDF is simultaneously deposited onto the printed filament scaffold. To achieve an industrially relevant overall electrode composition of AM:CB:PVDF = 90:5:5, the formulation of the dry powder layer was carefully adjusted. Although the 3D-printed filament contains a high fraction of PVDF to ensure sufficient mechanical strength during extrusion and printing, its mass contribution to the final electrode is relatively small. Therefore, the dry powder deposited during 3D printing was modified and designed to contain slight amount of PVDF, enabling the combined printed filament layer and powder layer to yield the targeted commercial ratio while maintaining strong structural integrity. Following powder deposition, the electrode undergoes heat-assisted rolling, which densifies the powder layer, strengthens interfacial bonding, and results in a dense and mechanically stable high loading electrode. Because the entire RED route is solvent-free, it avoids viscosity constraints, drying-induced nonuniformities. The resulting electrodes exhibit strong structural robustness and more favorable ion-transport architecture compared with slurry-cast counterparts, consistent with the reduced tortuosity and improved Li-ion diffusion illustrated in the diagram. To further evaluate industrial relevance, 30 × 30 mm pouch-cell electrodes are prepared and paired with graphite anodes designed with an N/P ratio of 1.1. These pouch cells have been used to assess long-term cycling stability, rate performance, and mechanical durability under different conditions. Overall, this work presents a solvent-free and energy-efficient dry manufacturing pathway for high-performance LIB electrodes. The RED approach not only eliminates the environmental and economic drawbacks of NMP-based slurry processes but also enables controllable electrode microstructures that enhance ion transport and mechanical integrity. This method provides a promising direction toward sustainable, high-loading, and industrially scalable electrode manufacturing for next-generation LIBs. Figure 1
Zitieren
APA
Shen, Y., Zhou, J., Ning, F., & Ma, X. (2026). A Novel Rolling-Assisted, Extrusion-Based Dry 3D Printing Process for High-Loading Lithium-Ion Battery Electrodes. ECS Meeting Abstracts, MA2026-01(2), 154-154. https://doi.org/10.1149/ma2026-012154mtgabs
Vancouver
Shen Y, Zhou J, Ning F, Ma X. A Novel Rolling-Assisted, Extrusion-Based Dry 3D Printing Process for High-Loading Lithium-Ion Battery Electrodes. ECS Meeting Abstracts. 2026;MA2026-01(2):154-154. doi:10.1149/ma2026-012154mtgabs
BibTeX
@article{Shen2026,
author = {Shen, Yihao and Zhou, Jianming and Ning, Fuda and Ma, Xiaotu},
title = {A Novel Rolling-Assisted, Extrusion-Based Dry 3D Printing Process for High-Loading Lithium-Ion Battery Electrodes},
journal = {ECS Meeting Abstracts},
year = {2026},
volume = {MA2026-01},
number = {2},
pages = {154--154},
doi = {10.1149/ma2026-012154mtgabs}
}
EUVIMED