EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Electrochemical Control of Cu/Ta Interfaces in Multistage Through-Glass Via Planarization

Charmy Ketankumar Jani, Maithreyan Venkatraman, Jihoon Seo, Shelby Nelson, Kyle Liddle, Sitaraman Krishnan

ECS Journal of Solid State Science and Technology · 06.11.2026

DOI: 10.1149/2162-8777/aebefa ↗

Kurz gefasst

Fachartikel in der Zeitschrift ECS Journal of Solid State Science and Technology, online erschienen am 06.11.2026. Verfasst von Charmy Ketankumar Jani und 5 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Center for Advanced Materials Processing, Clarkson University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Chemical mechanical planarization (CMP) of copper-filled through-glass vias (TGVs) requires sequentially removing the Cu overburden and Ta barrier while controlling Cu dishing and glass roughness. Electrochemical, dissolution, CMP removal-rate, direct Cu–Ta galvanic, and patterned-TGV polishing measurements were combined to examine how slurry chemistry affects these evolving interfaces. Increasing oxalic acid concentration strongly activated Cu, whereas Ta remained passive, with corrosion current densities below approximately 0.01 μA cm⁻² throughout the acidic ligand-series experiments, providing a basis for Cu/Ta selectivity. Benzotriazole (BTA) inhibition depended strongly on pH. At pH 5, BTA suppressed Cu corrosion and dissolution, whereas at pH 10 it substantially reduced dissolution without decreasing the Tafel-derived corrosion current. Direct coupling measurements demonstrated that isolated Cu–Ta corrosion-potential differences did not reliably predict galvanic current. At pH 10, 10 mM BTA reduced galvanic-current magnitude by approximately 61%. Increasing hydrogen peroxide concentration enhanced bulk Cu removal while Ta removal remained comparatively low. Patterned-TGV polishing revealed a trade-off: alkaline barrier finishing yielded the lowest glass RMS roughness (0.56 nm), whereas acidic barrier finishing yielded the lowest mean Cu dishing (0.37 μm). Effective TGV planarization therefore requires stage-specific control of slurry chemistry and polishing conditions rather than optimization using a single electrochemical or removal metric.

Förderung

  • Center for Advanced Materials Processing, Clarkson University

Zitieren

APA

Jani, C. K., Venkatraman, M., Seo, J., Nelson, S., Liddle, K., & Krishnan, S. (2026). Electrochemical Control of Cu/Ta Interfaces in Multistage Through-Glass Via Planarization. ECS Journal of Solid State Science and Technology. https://doi.org/10.1149/2162-8777/aebefa

Vancouver

Jani CK, Venkatraman M, Seo J, Nelson S, Liddle K, Krishnan S. Electrochemical Control of Cu/Ta Interfaces in Multistage Through-Glass Via Planarization. ECS Journal of Solid State Science and Technology. 2026. doi:10.1149/2162-8777/aebefa

BibTeX
@article{Jani2026,
  author = {Jani, Charmy Ketankumar and Venkatraman, Maithreyan and Seo, Jihoon and Nelson, Shelby and Liddle, Kyle and Krishnan, Sitaraman},
  title = {Electrochemical Control of Cu/Ta Interfaces in Multistage Through-Glass Via Planarization},
  journal = {ECS Journal of Solid State Science and Technology},
  year = {2026},
  doi = {10.1149/2162-8777/aebefa}
}
Kostenlos starten →