EUVIMEDEUVIMED entdecken
Crossref

Wet etch clean-up of plasma damage for 1.68 kV breakdown in NiO/β-Ga2O3 chlorine-etched PN diodes

Audrey Rose Gutierrez, Joseph A. Spencer, Alan G. Jacobs, Yuan Qin, Jenifer R. Hajzus, Hannah N. Masten, Emma Rocco, Karl D. Hobart, Travis J. Anderson, Yuhao Zhang, Akito Kuramata, Marko J. Tadjer

Journal of Vacuum Science & Technology A · 01.05.2025 · 43 (3)

DOI: 10.1116/6.0004289 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Vacuum Science & Technology A, online erschienen am 01.05.2025. Verfasst von Audrey Rose Gutierrez und 11 weiteren Autor:innen. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 62 Literaturangaben. Gefördert von: National Research Council, Office of Naval Research, Office of Naval Research Global.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The effectiveness of relevant wet chemical treatments in mitigating post-dry etch plasma damage to β-Ga2O3 prior to NiO heterojunction formation was investigated using electrical and surface characterization techniques. Wet etches of warm (80 °C) H3PO4, (70 °C) tetramethylammonium hydroxide (TMAH), and room-temperature 10:1 dilute HCl were used as post-BCl3 plasma etch treatments prior to the formation of β-Ga2O3-NiO PN heterojunction diodes and β-Ga2O3 Schottky barrier diodes (SBDs). Remarkably, all etched and treated SBDs displayed low ideality factors (1.04–1.07), while the breakdown voltages (VBD) and specific on-resistances (RON,SP) varied significantly across treatments, indicating that ideality alone cannot distinguish best practices in surface preparation techniques. The most successful treatment was a TMAH (70 °C, 10%, and 2 min), resulting in PN diodes with high VBD and low RON,SP of 1680 V and 4.78 mΩ cm2, respectively. The HCl-treated sample (1550 V) performed similarly in VBD to the etched and untreated control PN diodes (1580 V), improved the breakdown performance for the SBD devices (860 V HCl, 780 V untreated), and improved RON,SP in both cases—3.75 mΩ cm2 HCl vs 4.36 mΩ cm2 untreated for SBDs and 5.10 mΩ cm2 HCl vs 5.57 mΩ cm2 untreated for PN diodes. However, the warm H3PO4 treatment (1500 V VBD, 4.57 mΩ cm2RON,SP) caused a decrease in PN breakdown performance despite exhibiting the lowest RON,SP. All treated samples were similar in RMS roughness by AFM characterization, but showed significant differences in XPS characterization, indicating that surface contamination rather than a roughened surface affected the breakdown performance of devices.

Förderung

  • National Research Council
  • Office of Naval Research
  • Office of Naval Research Global

Zitieren

APA

Gutierrez, A. R., Spencer, J. A., Jacobs, A. G., Qin, Y., Hajzus, J. R., Masten, H. N., Rocco, E., Hobart, K. D., Anderson, T. J., Zhang, Y., Kuramata, A., & Tadjer, M. J. (2025). Wet etch clean-up of plasma damage for 1.68 kV breakdown in NiO/β-Ga2O3 chlorine-etched PN diodes. Journal of Vacuum Science & Technology A, 43(3). https://doi.org/10.1116/6.0004289

Vancouver

Gutierrez AR, Spencer JA, Jacobs AG, Qin Y, Hajzus JR, Masten HN, et al. Wet etch clean-up of plasma damage for 1.68 kV breakdown in NiO/β-Ga2O3 chlorine-etched PN diodes. Journal of Vacuum Science & Technology A. 2025;43(3). doi:10.1116/6.0004289

BibTeX
@article{Gutierrez2025,
  author = {Gutierrez, Audrey Rose and Spencer, Joseph A. and Jacobs, Alan G. and Qin, Yuan and Hajzus, Jenifer R. and Masten, Hannah N. and Rocco, Emma and Hobart, Karl D. and Anderson, Travis J. and Zhang, Yuhao and Kuramata, Akito and Tadjer, Marko J.},
  title = {Wet etch clean-up of plasma damage for 1.68 kV breakdown in NiO/β-Ga2O3 chlorine-etched PN diodes},
  journal = {Journal of Vacuum Science & Technology A},
  year = {2025},
  volume = {43},
  number = {3},
  doi = {10.1116/6.0004289}
}
Kostenlos starten →