EUVIMEDEUVIMED entdecken
Crossref

Windage Torque Reduction in Low-Pressure Turbine Cavities Part II: Experimental and Numerical Results

Richard W. Jackson, Zhihui Li, Loizos Christodoulou, Stephen Ambrose, Carl M. Sangan, Richard Jefferson-Loveday, Gary D. Lock, James A. Scobie

Journal of Turbomachinery · 01.06.2024 · 146 (6)

DOI: 10.1115/1.4063876 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Turbomachinery, online erschienen am 29.01.2024. Verfasst von Richard W. Jackson und 7 weiteren Autor:innen. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 22 Literaturangaben. Gefördert von: Cleansky.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Minimizing the losses within a low-pressure turbine (LPT) system is critical for the design of next-generation ultra-high bypass ratio aero-engines. The stator-well cavity windage torque can be a significant source of loss within the system, influenced by the ingestion of mainstream annulus air with a tangential velocity opposite to that of the rotor. This paper presents experimental and numerical results of three carefully designed Flow Control Concepts (FCCs)—additional geometric features on the stator surfaces, which were optimized to minimize the windage torque within a scaled, engine-representative stator-well cavity. FCC1 and FCC2 featured rows of guide vanes at the inlet to the downstream and upstream wheel-spaces, respectively. FCC3 combined FCC1 and FCC2. Superposed flows were introduced to the upstream section of the cavity, which modelled the low-radius coolant and higher radius leakage between the rotor blades. In addition to torque measurements, total and static pressures were collected, from which the cavity swirl ratio was derived. Additional swirl measurements were collected using a five-hole aerodynamic probe, which traversed radially at the entrance and exit of the cavity. A cavity windage torque reduction of 55% on the baseline (which has no flow control) was measured for FCC3, at the design condition with superposed flow. For this concept, an increase in the cavity swirl in both the upstream and downstream wheel-spaces was demonstrated experimentally and numerically. With increasing superposed flow, the contribution of FCC1 surpassed FCC2, due to more mass flow entering the downstream wheel-space across the rotor fins (passing FCC1), and less ingestion from the annulus into the upstream wheel-space (passing FCC2). The torque changes from the concepts are explained using the fluid dynamic evidence from experimental swirl measurements and computational simulations. The simulations allow translation to engine-operating conditions and practical information to the engine designer.

Förderung

  • Cleansky

Zitieren

APA

Jackson, R. W., Li, Z., Christodoulou, L., Ambrose, S., Sangan, C. M., Jefferson-Loveday, R., Lock, G. D., & Scobie, J. A. (2024). Windage Torque Reduction in Low-Pressure Turbine Cavities Part II: Experimental and Numerical Results. Journal of Turbomachinery, 146(6). https://doi.org/10.1115/1.4063876

Vancouver

Jackson RW, Li Z, Christodoulou L, Ambrose S, Sangan CM, Jefferson-Loveday R, et al. Windage Torque Reduction in Low-Pressure Turbine Cavities Part II: Experimental and Numerical Results. Journal of Turbomachinery. 2024;146(6). doi:10.1115/1.4063876

BibTeX
@article{Jackson2024,
  author = {Jackson, Richard W. and Li, Zhihui and Christodoulou, Loizos and Ambrose, Stephen and Sangan, Carl M. and Jefferson-Loveday, Richard and Lock, Gary D. and Scobie, James A.},
  title = {Windage Torque Reduction in Low-Pressure Turbine Cavities Part II: Experimental and Numerical Results},
  journal = {Journal of Turbomachinery},
  year = {2024},
  volume = {146},
  number = {6},
  doi = {10.1115/1.4063876}
}
Kostenlos starten →