EUVIMEDEUVIMED entdecken
Open Access

Automated In-Process Cure Monitoring of Composite Laminates Using a Guided Wave-Based System With High-Temperature Piezoelectric Transducers

Tyler B Hudson, Fuh-Gwo Yuan

Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems · 2018

DOI: 10.1115/1.4039230 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems, 2018. Verfasst von Tyler B Hudson und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Aerospace Engineering, North Carolina State University, 911 Oval Drive-3306 EBIII, Campus Box 7910, Raleigh, NC 27695; N…. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: Aeronautics NASA, Langley Research Center.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An in-process cure monitoring technique based on “guided wave” concept for carbon fiber reinforced polymer (CFRP) composites was developed. Key parameters including physical properties (viscosity and degree of cure) and state transitions (gelation and vitrification) during the cure cycle were clearly identified experimentally from the amplitude and group velocity of guided waves, validated via the semi-empirical cure process modeling software RAVEN. Using the newly developed cure monitoring system, an array of high-temperature piezoelectric transducers acting as an actuator and sensors were employed to excite and sense guided wave signals, in terms of voltage, through unidirectional composite panels fabricated from Hexcel® IM7/8552 prepreg during cure in an oven. Average normalized peak voltage, which pertains to the wave amplitude, was selected as a metric to describe the guided waves phenomena throughout the entire cure cycle. During the transition from rubbery to glassy state, the group velocity of the guided waves was investigated for connection with degree of cure, Tg, and mechanical properties. This work demonstrated the feasibility of in-process cure monitoring and continued progress toward a closed-loop process control to maximize composite part quality and consistency.

Autor:innen und Institutionen

  • Department of Mechanical and Aerospace Engineering, North Carolina State University, 911 Oval Drive-3306 EBIII, Campus Box 7910, Raleigh, NC 27695; National Institute of Aerospace, 100 Exploration Way, Hampton, VA 23666.

Förderung

  • Aeronautics NASA
  • Langley Research Center

Zitieren

APA

Hudson, T. B., & Yuan, F. G. (2018). Automated In-Process Cure Monitoring of Composite Laminates Using a Guided Wave-Based System With High-Temperature Piezoelectric Transducers. Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems. https://doi.org/10.1115/1.4039230

Vancouver

Hudson TB, Yuan FG. Automated In-Process Cure Monitoring of Composite Laminates Using a Guided Wave-Based System With High-Temperature Piezoelectric Transducers. Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems. 2018. doi:10.1115/1.4039230

BibTeX
@article{Hudson2018,
  author = {Hudson, Tyler B and Yuan, Fuh-Gwo},
  title = {Automated In-Process Cure Monitoring of Composite Laminates Using a Guided Wave-Based System With High-Temperature Piezoelectric Transducers},
  journal = {Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems},
  year = {2018},
  doi = {10.1115/1.4039230}
}
Kostenlos starten →