EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Optical stability of 3D‐printed and milled zirconia after artificial aging and immersion in liquids: An in vitro study

Athanasios E Rigos, Matthew J Kesterke, Jenn-Hwan Chen, Eleana Kontonasaki, Elias D Kontogiorgos

Journal of Prosthodontics · 2026-03 · 35 (3) · 375-381

DOI: 10.1111/jopr.14090 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 23.06.2025. Verfasst von Athanasios E Rigos und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Comprehensive Dentistry, College of Dentistry, Texas A&M University, Dallas, Texas, USA. Hauptthemen laut MEDLINE: Zirconium, Printing, Three-Dimensional, Dental Materials. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: American College of Prosthodontists Education Foundation Research Fellowship Grant.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To assess the impact of artificial aging and immersion in common liquids on the optical properties of 3D‐printed and milled zirconia. Materials and Methods Monolithic zirconia discs ( N = 100) were fabricated using two methods: 3Y‐TZP for milling (e.max ZirCAD LT BL, Ivoclar Vivadent) and printable 3Y‐TZP material (LithaCon 3Y 230) for 3D printing. The flat surfaces of the discs were mechanically polished. Color measurements were taken at baseline, after 10,000 thermal cycles and storage in various liquids for 20 days ( T 1 ), and after 20,000 thermal cycles and storage for 40 days ( T 2 ) using a spectrophotometer. Samples were stored in distilled water, tea, coffee, red wine, or Coca‐Cola ( n = 10 per group). Color differences (Δ E ) were calculated between baseline and T 1 as well as baseline and T 2 using the CIEDE2000 formula, while contrast ratio (CR) and translucency parameter (TP) were calculated for each time point. Kruskal–Wallis nonparametric tests with Bonferroni corrections were used for comparisons between zirconia types, liquids, and time points. Shapiro–Wilk tests were applied for time‐point comparisons ( α ≤ 0.05).

Results

At T 1 and T 2 , significant differences in TP and CR were observed after storage in tea, coffee, and red wine for both zirconia types. Δ E values following immersion in distilled water remained below clinically perceptible levels, while tea, wine, and coffee resulted in unacceptable Δ E at T 1 and T 2 .

Conclusions

3D‐printed and milled zirconia demonstrated comparable color stability after artificial aging and immersion in common liquids, with no significant differences between the materials in terms of color change (Δ E ).

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumPrinting, Three-DimensionalDental MaterialsImmersionColorCoffeeMaterials TestingIn Vitro TechniquesWineSpectrophotometrySurface PropertiesWaterTea

Substanzen

Zirconiumzirconium oxideCoffeeDental MaterialsWaterTea

Autor:innen und Institutionen

  • Department of Comprehensive Dentistry, College of Dentistry, Texas A&M University, Dallas, Texas, USA.
  • Department of Orthodontics, College of Dentistry, Texas A&M University, Dallas, Texas, USA.
  • Department of Prosthodontics, School of Dentistry, Faculty of Health Sciences, Aristotle University of Thessaloniki, Thessaloniki, Greece.

Förderung

  • American College of Prosthodontists Education Foundation Research Fellowship Grant

Zitieren

APA

Rigos, A. E., Kesterke, M. J., Chen, J. H., Kontonasaki, E., & Kontogiorgos, E. D. (2026). Optical stability of 3D‐printed and milled zirconia after artificial aging and immersion in liquids: An in vitro study. Journal of Prosthodontics, 35(3), 375-381. https://doi.org/10.1111/jopr.14090

Vancouver

Rigos AE, Kesterke MJ, Chen JH, Kontonasaki E, Kontogiorgos ED. Optical stability of 3D‐printed and milled zirconia after artificial aging and immersion in liquids: An in vitro study. Journal of Prosthodontics. 2026;35(3):375-381. doi:10.1111/jopr.14090

BibTeX
@article{Rigos2026,
  author = {Rigos, Athanasios E and Kesterke, Matthew J and Chen, Jenn-Hwan and Kontonasaki, Eleana and Kontogiorgos, Elias D},
  title = {Optical stability of 3D‐printed and milled zirconia after artificial aging and immersion in liquids: An in vitro study},
  journal = {Journal of Prosthodontics},
  year = {2026},
  volume = {35},
  number = {3},
  pages = {375--381},
  doi = {10.1111/jopr.14090}
}
Kostenlos starten →