EUVIMEDEUVIMED entdecken
Crossref

Effect of daily immersion of different beverages on the surface roughness and color stability of 3D‐printed denture base resins

Mohammed M Gad iD, Hassan Alramadan, Mohammed Alkoudemi, Hussain Aljubran, Raand Altayyar, Deena Alghamdi, Nadim Z Baba iD, Soban Q Khan iD, Reem Abualsaud iD, Ahmed Fathey Elhagali iD, Fahad A Al-Harbi iD

Journal of Prosthodontics · 26.11.2024

DOI: 10.1111/jopr.13993 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 26.11.2024. Verfasst von Mohammed M Gad und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 39 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To measure the effect of daily immersion in varying beverages (distilled water, tea, carbonated beverage, and orange juice) on surface roughness and color stability of 3D‐printed denture base resins. Materials and Methods 160 acrylic resin discs (15 × 2.5 mm) were made from heat‐polymerized (HP), and 3D‐printed resins (FormLabs, ASIGA, and NextDent). Resin discs ( N = 40) were immersed in different solutions (distilled water, tea, carbonated beverage, or orange juice; ( n = 10/group)). Surface roughness ( R a , µm) was measured initially ( T 0 ), 6 months post immersion ( T 1 ), and 12 months post immersion ( T 2 ) using a non‐contact profilometer. Color change (∆ E 00 ) was calculated using CIEL2000 at T 1 and T 2 using a spectrophotometer. The data were analyzed using Mann‐Whitney U test and Kruskal‐Wallis test in addition to general linear modeling ( α = 0.05).

Results

Significant differences in surface roughness ( R a ) were found between the baseline and immersion in distilled water, carbonated beverage, and orange juice ( p < 0.05). HP resin showed increased roughness with all immersion solutions compared to T 0 with the highest value seen at T 1 with tea. ASIGA resin had the highest mean R a of 1.78 (0.43) after carbonated beverage immersion, while FormLabs resin had the lowest mean R a of 0.88 (0.06) after distilled water immersion. Tea immersion did not significantly affect R a among the resins ( p > 0.05). Noticeable color changes were observed after immersion in tea, carbonated beverage, and orange juice. All resins exceeded perceptibility and acceptability thresholds at T 1 and T 2 . The combined effect of time and resin on color change was statistically significant ( p < 0.001), while the combined effects of time/immersion solution, immersion solution/resin, and immersion solution/resin/time were not.

Conclusion

Carbonated beverage, tea, and orange juice increase the surface roughness of 3D‐printed resins. Tea, carbonated beverage, and orange juice resulted in noticeable color changes of HP and 3D‐printed denture base resins and this change was time‐dependent.

Schlagwörter

Stichwörter der Autor:innen

3D printingbeveragescolor stabilityimmersionstaining solutionssurface properties

Autor:innen und Institutionen

  • Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Advanced Specialty Education Program in Implant Dentistry, Loma Linda University, School of Dentistry, California, USA.
  • Department of Dental Education, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam, Saudi Arabia.
  • Department of Removable Prosthodontics, Faculty of Dental Medicine, Al-Azhar University, Assiut, Egypt.

ORCID-Profile: Mohammed M Gad, Nadim Z Baba, Soban Q Khan, Reem Abualsaud, Ahmed Fathey Elhagali, Fahad A Al-Harbi

Zitieren

APA

Gad, M. M., Alramadan, H., Alkoudemi, M., Aljubran, H., Altayyar, R., Alghamdi, D., Baba, N. Z., Khan, S. Q., Abualsaud, R., Elhagali, A. F., & Al-Harbi, F. A. (2024). Effect of daily immersion of different beverages on the surface roughness and color stability of 3D‐printed denture base resins. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13993

Vancouver

Gad MM, Alramadan H, Alkoudemi M, Aljubran H, Altayyar R, Alghamdi D, et al. Effect of daily immersion of different beverages on the surface roughness and color stability of 3D‐printed denture base resins. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13993

BibTeX
@article{Gad2024,
  author = {Gad, Mohammed M and Alramadan, Hassan and Alkoudemi, Mohammed and Aljubran, Hussain and Altayyar, Raand and Alghamdi, Deena and Baba, Nadim Z and Khan, Soban Q and Abualsaud, Reem and Elhagali, Ahmed Fathey and Al-Harbi, Fahad A},
  title = {Effect of daily immersion of different beverages on the surface roughness and color stability of 3D‐printed denture base resins},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13993}
}
Kostenlos starten →