EUVIMEDEUVIMED entdecken
Crossref

Comparison of mechanical properties, surface roughness, and color stability of 3D-printed and conventional heat-polymerizing denture base materials

Mehran Falahchai, Mehrsima Ghavami-Lahiji, Vanya Rasaie, Mohammad Amin, Hamid Neshandar Asli

The Journal of Prosthetic Dentistry · 2023-08 · 130 (2) · 266.e1-266.e8

DOI: 10.1016/j.prosdent.2023.06.006 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023-08. Verfasst von Mehran Falahchai und 4 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Prosthodontics, Dental Sciences Research Center, School of Dentistry, Guilan University of Medical Sciences, Rasht…. Hauptthemen laut MEDLINE: Denture Bases, Hot Temperature. Die Arbeit wurde bisher 60-mal zitiert (Crossref) und nennt 37 Literaturangaben. Gefördert von: Guilan University of Medical Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Studies on the mechanical, optical, and surface properties of 3-dimensionally (3D) printed denture base materials are scarce, and those available have reported conflicting results. PURPOSE: The purpose of this in vitro study was to compare the mechanical properties, surface roughness, and color stability of 3D-printed and conventional heat-polymerizing denture base materials. MATERIAL AND METHODS: A total of 34 rectangular specimens (64×10×3.3 mm) were fabricated from each of the conventional (SR Triplex Hot; Ivoclar AG) and 3D-printed (Denta base; Asiga) denture base materials. All specimens underwent coffee thermocycling for 5000 cycles, and half in each group (n=17) were evaluated in terms of color parameters, color change (ΔE00), and surface roughness (Ra) before and after coffee thermocycling. The specimens then underwent a 3-point bend test. The remaining specimens in each group (n=17) underwent impact strength and Vickers hardness testing. Data were analyzed by the paired samples, independent samples, and Wilcoxon signed rank tests (α=.05). RESULTS: The color change caused by coffee thermocycling in the 3D-printed group was higher than that in the conventional group (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture BasesHot TemperatureCoffeeMaterials TestingSurface PropertiesPrinting, Three-DimensionalColor

Substanzen

Coffee

Autor:innen und Institutionen

  • Associate Professor, Department of Prosthodontics, Dental Sciences Research Center, School of Dentistry, Guilan University of Medical Sciences, Rasht, Iran.
  • Associate Professor, Department of Prosthodontics, Dental Sciences Research Center, School of Dentistry, Guilan University of Medical Sciences, Rasht, Iran; Assistant Professor, Dental Sciences Research Center, Departme…
  • Researcher, Department of Prosthodontics, Dental Research Center, Dentistry Research Institute, Tehran University of Medical Sciences, Tehran, Iran.

Förderung

  • Guilan University of Medical Sciences

Zitieren

APA

Falahchai, M., Ghavami-Lahiji, M., Rasaie, V., Amin, M., & Neshandar Asli, H. (2023). Comparison of mechanical properties, surface roughness, and color stability of 3D-printed and conventional heat-polymerizing denture base materials. The Journal of Prosthetic Dentistry, 130(2), 266.e1-266.e8. https://doi.org/10.1016/j.prosdent.2023.06.006

Vancouver

Falahchai M, Ghavami-Lahiji M, Rasaie V, Amin M, Neshandar Asli H. Comparison of mechanical properties, surface roughness, and color stability of 3D-printed and conventional heat-polymerizing denture base materials. The Journal of Prosthetic Dentistry. 2023;130(2):266.e1-266.e8. doi:10.1016/j.prosdent.2023.06.006

BibTeX
@article{Falahchai2023,
  author = {Falahchai, Mehran and Ghavami-Lahiji, Mehrsima and Rasaie, Vanya and Amin, Mohammad and Neshandar Asli, Hamid},
  title = {Comparison of mechanical properties, surface roughness, and color stability of 3D-printed and conventional heat-polymerizing denture base materials},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2023},
  volume = {130},
  number = {2},
  pages = {266.e1--266.e8},
  doi = {10.1016/j.prosdent.2023.06.006}
}
Kostenlos starten →