EUVIMEDEUVIMED entdecken
Crossref

Effect of cleaning solution on surface properties of 3D‐printed denture materials

Marina Rodrigues Santi, Nadima Khodor iD, Michael Sekula, David Donatelli, Grace Mendonça De Souza iD

Journal of Prosthodontics · 2026

DOI: 10.1111/jopr.13936 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2026. Verfasst von Marina Rodrigues Santi und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Piracicaba Dental School, University of Campinas, Piracicaba, Sao Paulo, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Denture Cleansers, Dental Materials. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 27 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the effect of cleaning solutions on surface properties of 3D‐printed resins. Materials and Methods Seven different resin materials for denture base and teeth were used in the form of 280 half‐disks. Samples were randomly assigned to two cleaning groups (FD, FreshDent; PO, Polydent), with daily 2‐ or 3‐min immersion followed by water storage, repeated for 30 days. Samples were then cleaned in an ultrasonic bath with water and analyzed for surface roughness (Keyence, VHX‐7000N) and hardness (Shimadzu, HMV‐2 series). The pH of cleaning solutions was analyzed over 5‐min and the surface morphology of specimens was analyzed via scanning electron microscopy (SEM). Statistical analysis used two‐way ANOVA ( α = 0.05).

Results

Surface roughness of base materials was significantly affected ( p < 0.001), whereas roughness of teeth materials was not. As for hardness, there was a significant interaction between materials and cleaning solution for both, base ( p < 0.001) and teeth ( p < 0.001). For teeth materials, PO significantly increased Denture's (Dentca) hardness and decreased that of Rodin's (Pac Dent), while PO significantly increased Rodin's Base (Pac Dent) hardness. The hardness of Flexcera Ultra (Envision Tec), Glidewell (Glidewell), Lucitone (Dentsply Sirona), and NextDent (NextDent) teeth and base materials were not affected by the cleaning solution. Overall, the pH of FD averaged 7.3 and PO averaged 6.6. All the SEM images indicated surface irregularities after immersion in either FD or PO.

Conclusions

One‐month of storage and cyclic cleaning of 3D‐ printed resins did not affect surface roughness but had a significant impact on hardness. The cleaning solutions’ effect was not homogeneous among materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDenture CleansersDental MaterialsSurface PropertiesMicroscopy, Electron, ScanningMaterials TestingDenture BasesHardnessHydrogen-Ion Concentration

Stichwörter der Autor:innen

3D printingadditive manufacturingdental prosthesismechanical properties

Substanzen

Denture CleansersDental Materials

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Piracicaba Dental School, University of Campinas, Piracicaba, Sao Paulo, Brazil.
  • Department of Rehabilitative and Reconstructive Dentistry, University of Louisville, School of Dentistry, Louisville, Kentucky, USA.
  • Department of Bioinformatics and Biostatistics, University of Louisville, School of Dentistry, University of Louisville, Louisville, Kentucky, USA.
  • Department of Comprehensive Dentistry, University of Louisville, School of Dentistry, Louisville, Kentucky, USA.

ORCID-Profile: Nadima Khodor, Grace Mendonça De Souza

Zitieren

APA

Santi, M. R., Khodor, N., Sekula, M., Donatelli, D., & De Souza, G. M. (2026). Effect of cleaning solution on surface properties of 3D‐printed denture materials. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13936

Vancouver

Santi MR, Khodor N, Sekula M, Donatelli D, De Souza GM. Effect of cleaning solution on surface properties of 3D‐printed denture materials. Journal of Prosthodontics. 2026. doi:10.1111/jopr.13936

BibTeX
@article{Santi2026,
  author = {Santi, Marina Rodrigues and Khodor, Nadima and Sekula, Michael and Donatelli, David and De Souza, Grace Mendonça},
  title = {Effect of cleaning solution on surface properties of 3D‐printed denture materials},
  journal = {Journal of Prosthodontics},
  year = {2026},
  doi = {10.1111/jopr.13936}
}
Kostenlos starten →