EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY-NC-ND 4.0

Seating accuracy of removable partial denture frameworks fabricated by different digital workflows in comparison to conventional workflow

Andrea Korkes, Janine Jomaa, Anastasios Kavouris, Tahyr Lalani, Phillip King, Samantha Lee, Hongyi Li, Aixi Li, Wilson Khuu, Ka Ho Jesper Law, Jaafar Abduo iD

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13923 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Andrea Korkes und 10 weiteren Autor:innen. Beteiligte Einrichtung: Restorative Section, Melbourne Dental School, Melbourne University, Melbourne, Victoria, Australia. Hauptthemen laut MEDLINE: Denture, Partial, Removable, Denture Design, Computer-Aided Design, Workflow. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Melbourne Dental School Research Higher Degree Funding.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the seating accuracy of removable partial denture (RPD) frameworks fabricated by two digital workflows involving selective laser melting (SLM) in comparison to the conventional workflow. Materials and Methods A Kennedy class III modification 1 partially edentulous mandibular arch was used as a master model. Three RPD framework groups were included: (1) a conventional workflow group with conventional impression and casting (CC), (2) a partial digital workflow group with conventional impression and digital fabrication (CD), and (3) a complete digital workflow group with digital impression and digital fabrication (DD). A total of 10 frameworks were produced for each group. The marginal gaps at the occlusal rests, retention arms, and reciprocating arms were measured by a traveling microscope. The data were analyzed with the one‐way analysis of variance test.

Results

At the framework level, the most superior fit was observed for the CD group (79.5 µm) followed by DD (85.3 µm) and CC (114.2 µm) groups. The CD and DD groups were significantly superior to CC ( p < 0.001). This fit pattern was consistent for the retention and reciprocating arms, while the occlusal rest fit was similar among all the groups.

Conclusions

The SLM frameworks had a promising seating accuracy in comparison to conventional frameworks. The type of impression, conventional or digital, did not affect the accuracy of SLM frameworks. The differences observed in the present study are likely to be of minimal clinical significance.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Denture, Partial, RemovableDenture DesignComputer-Aided DesignWorkflowHumansDental Casting TechniqueDental Impression TechniqueLasersDenture RetentionDental Marginal AdaptationModels, DentalJaw, Edentulous, PartiallySurface PropertiesMandible

Stichwörter der Autor:innen

additive manufacturingcastingintraoral scanningmarginal gapselective laser melting

Autor:innen und Institutionen

  • Restorative Section, Melbourne Dental School, Melbourne University, Melbourne, Victoria, Australia.

ORCID-Profile: Jaafar Abduo

Förderung

  • Melbourne Dental School Research Higher Degree Funding

Zitieren

APA

Korkes, A., Jomaa, J., Kavouris, A., Lalani, T., King, P., Lee, S., Li, H., Li, A., Khuu, W., Law, K. H. J., & Abduo, J. (2024). Seating accuracy of removable partial denture frameworks fabricated by different digital workflows in comparison to conventional workflow. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13923

Vancouver

Korkes A, Jomaa J, Kavouris A, Lalani T, King P, Lee S, et al. Seating accuracy of removable partial denture frameworks fabricated by different digital workflows in comparison to conventional workflow. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13923

BibTeX
@article{Korkes2024,
  author = {Korkes, Andrea and Jomaa, Janine and Kavouris, Anastasios and Lalani, Tahyr and King, Phillip and Lee, Samantha and Li, Hongyi and Li, Aixi and Khuu, Wilson and Law, Ka Ho Jesper and Abduo, Jaafar},
  title = {Seating accuracy of removable partial denture frameworks fabricated by different digital workflows in comparison to conventional workflow},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13923}
}
Kostenlos starten →