EUVIMEDEUVIMED entdecken
Crossref

The effect of different abutment and restorative crown materials on stress distribution in single‐unit implant‐supported restorations: A 3D finite element stress analysis

Gülsüm Gökçimen iD, Rukiye Durkan iD, Gonca Deste Gökay iD, Perihan Oyar iD

Journal of Prosthodontics · 2024

DOI: 10.1111/jopr.13732 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, 2024. Verfasst von Gülsüm Gökçimen und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Ankara 75th year Oral and Dental Health Hospital, Ankara, Türkiye. Hauptthemen laut MEDLINE: Finite Element Analysis, Crowns, Dental Stress Analysis, Dental Prosthesis, Implant-Supported. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 45 Literaturangaben. Gefördert von: Afyonkarahisar Health Sciences University Board of Scientific Research Projects.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the effect of restorative materials with or without resin content, modeled on zirconia and titanium abutment materials, on the stress distribution on the alveolar bone, implant, and prosthetic crowns with a 3D finite element stress analysis. Material and Methods Titanium and zirconia abutments were combined with three implant‐supported crown materials (polymer infiltrated hybrid ceramic (PICN), lithium disilicate (LD), and zirconia‐reinforced lithium silicate (ZLS)) to create six experimental groups. The 40 × 30 × 20 mm alveolar bone, 3.75 × 10 mm implant, esthetic abutment, and maxillary first premolar crown bonded over the abutment were the components of the finite element models. On the lingual cusp of the crown, the 150 N occlusal loading was applied in the buccolingual direction at a 30° angle. Equivalent von Mises stress and maximum and minimum principal stresses were used for both the qualitative and quantitative evaluation of the stress distribution of the created models.

Results

The von Mises stress in implant and abutment did not differ according to the crown materials. The use of a zirconia abutment resulted in higher von Mises stress values in the abutment but lower stress values in the implant. The highest stress values were obtained in ZLS (196.65 MPa) and LD (194.05 MPa) crowns. The use of titanium abutments, regardless of crown materials, resulted in higher von Mises stress values in restorative crowns than in zirconia abutments. The principal stress values in alveolar bone showed similar distribution and concentration in all models.

Conclusions

Changes in crown material did not affect stress distribution in the implant and peripheral bone. However, the zirconia esthetic abutment resulted in a lower stress concentration on the implant.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Finite Element AnalysisCrownsDental Stress AnalysisDental Prosthesis, Implant-SupportedTitaniumZirconiumDental AbutmentsHumansDental Implants, Single-ToothDental MaterialsDental PorcelainDental Implant-Abutment DesignCeramicsMaterials TestingAlveolar ProcessStress, Mechanical

Stichwörter der Autor:innen

CAD‐CAMfinite element analysisimplant

Substanzen

TitaniumZirconiumzirconium oxideDental MaterialsDental Porcelainlithia disilicate

Autor:innen und Institutionen

  • Department of Prosthodontics, Ankara 75th year Oral and Dental Health Hospital, Ankara, Türkiye.
  • Department of Prosthodontics, Faculty of Dentistry, Istanbul Okan University, Istanbul, Türkiye.
  • Department of Prosthodontics, Faculty of Dentistry, Bursa Uludağ University, Bursa, Türkiye.
  • Dental Prosthetics Technology, School of Health Services, Hacettepe University, Ankara, Türkiye.

ORCID-Profile: Gülsüm Gökçimen, Rukiye Durkan, Gonca Deste Gökay, Perihan Oyar

Förderung

  • Afyonkarahisar Health Sciences University Board of Scientific Research Projects

Zitieren

APA

Gökçimen, G., Durkan, R., Deste Gökay, G., & Oyar, P. (2024). The effect of different abutment and restorative crown materials on stress distribution in single‐unit implant‐supported restorations: A 3D finite element stress analysis. Journal of Prosthodontics. https://doi.org/10.1111/jopr.13732

Vancouver

Gökçimen G, Durkan R, Deste Gökay G, Oyar P. The effect of different abutment and restorative crown materials on stress distribution in single‐unit implant‐supported restorations: A 3D finite element stress analysis. Journal of Prosthodontics. 2024. doi:10.1111/jopr.13732

BibTeX
@article{Gkimen2024,
  author = {Gökçimen, Gülsüm and Durkan, Rukiye and Deste Gökay, Gonca and Oyar, Perihan},
  title = {The effect of different abutment and restorative crown materials on stress distribution in single‐unit implant‐supported restorations: A 3D finite element stress analysis},
  journal = {Journal of Prosthodontics},
  year = {2024},
  doi = {10.1111/jopr.13732}
}
Kostenlos starten →