EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Effect of thickness and CAD‐CAM material on fatigue resistance of endodontically treated molars restored with occlusal veneers

Mayara Dos Santos Noronha, Marco Aurélio de Carvalho, Anh Quynh Do, Vitaliano Gomes de Araújo Neto, Camila Heitor Campos, Marcelo Giannini, Pascal Magne

Journal of Prosthodontics · 2023-02 · 32 (2)

DOI: 10.1111/jopr.13606 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 02.10.2022. Verfasst von Mayara Dos Santos Noronha und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Piracicaba Dental School, University of Campinas, ‎São Paulo, Brazil. Hauptthemen laut MEDLINE: Dental Porcelain, Ceramics. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 66 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: São Paulo Research Foundation, National Council for Scientific and Technological Development, Fundação de Amparo à Pesquisa do Estado de São Paulo.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

To evaluate the influence of the thickness and type of computer‐aided design and computer‐aided manufacturing (CAD‐CAM) material on the fatigue resistance and failure mode of endodontically treated teeth (ETT) restored with occlusal veneers (OV). Materials and methods Seventy‐five (N = 75) ETT were restored with Herculite XRV in the endodontic access. Five experimental groups (n = 15) were tested. Four groups had two different thicknesses (0.6‐0.7 mm or 1.4‐1.6 mm) and two different CAD‐CAM materials: zirconia‐reinforced lithium‐silicate (LS/Celtra Duo) and composite resin (RC/Cerasmart). The fifth group (control) did not have occlusal veneers. All the specimens were subjected to accelerated fatigue (5 Hz frequency) with an occlusal load increasing up to 1800 N and 131,000 cycles. The number of cycles was recorded when the machine stopped or at the completion of the test. Fatigue resistance was analyzed using the Kaplan‐Meier survival test (95% significance level, log‐rank post hoc pairwise comparisons). The samples were categorized according to failure mode. The CAD‐CAM materials were examined through scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy (EDS).

Results

No differences were found between the thicknesses, regardless of the type of the CAD‐CAM material. The thick LS OV outperformed the RC and control groups. The thin RC OV and control groups showed a higher percentage of repairable and possibly repairable failures than the other groups. LS was more homogeneous under SEM, and the EDS analysis detected Si and Zr, but not Li.

Conclusions

A larger thickness did not improve the resistance of the CAD‐CAM materials. Thick LS showed a higher cumulative survival rate to fatigue than the RC and control groups. The direct composite alone (control) survived similarly to the experimental groups, except for the thick LS.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PorcelainCeramicsMaterials TestingDental Stress AnalysisComputer-Aided DesignMolar

Stichwörter der Autor:innen

CAD-CAMceramicscomposite resinsfatigue resistanceocclusal veneers

Substanzen

Dental Porcelain

Autor:innen und Institutionen

  • Department of Restorative Dentistry, Piracicaba Dental School, University of Campinas, ‎São Paulo, Brazil.
  • Department of Oral Rehabilitation, School of Dentistry, University of Anápolis, Anápolis, Brazil.
  • Advanced Endodontics, Herman Ostrow School of Dentistry, University of Southern California, Los Angeles, CA.
  • Department of Oral Rehabilitation, School of Dentistry, Federal Fluminense University, Nova Friburgo, Brazil.
  • Division of Restorative Sciences, Herman Ostrow School of Dentistry, University of Southern California, Los Angeles, CA.

Förderung

  • São Paulo Research Foundation
  • National Council for Scientific and Technological Development
  • Fundação de Amparo à Pesquisa do Estado de São Paulo
  • Conselho Nacional de Desenvolvimento Científico e Tecnológico

Zitieren

APA

Noronha, M. D. S., Carvalho, M. A., Do, A. Q., Neto, V. G. A., Campos, C. H., Giannini, M., & Magne, P. (2023). Effect of thickness and CAD‐CAM material on fatigue resistance of endodontically treated molars restored with occlusal veneers. Journal of Prosthodontics, 32(2). https://doi.org/10.1111/jopr.13606

Vancouver

Noronha MDS, Carvalho MA, Do AQ, Neto VGA, Campos CH, Giannini M, et al. Effect of thickness and CAD‐CAM material on fatigue resistance of endodontically treated molars restored with occlusal veneers. Journal of Prosthodontics. 2023;32(2). doi:10.1111/jopr.13606

BibTeX
@article{Noronha2023,
  author = {Noronha, Mayara Dos Santos and Carvalho, Marco Aurélio de and Do, Anh Quynh and Neto, Vitaliano Gomes de Araújo and Campos, Camila Heitor and Giannini, Marcelo and Magne, Pascal},
  title = {Effect of thickness and CAD‐CAM material on fatigue resistance of endodontically treated molars restored with occlusal veneers},
  journal = {Journal of Prosthodontics},
  year = {2023},
  volume = {32},
  number = {2},
  doi = {10.1111/jopr.13606}
}
Kostenlos starten →