Surface Characteristics and Flexural Strength of Porous‐Surface Designed Zirconia Manufactured via Stereolithography
Journal of Prosthodontics · 2023-04 · 32 (4)
DOI: 10.1111/jopr.13565 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Prosthodontics, online erschienen am 22.07.2022. Verfasst von Quanquan Ma und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Peking University School and Hospital of Stomatology & National Center of Stomatology & National Clinical Research Cent…. Hauptthemen laut MEDLINE: Flexural Strength, Stereolithography. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 38 Literaturangaben. Gefördert von: Guangdong Basic and Applied Basic Research Foundation, Capital Health Research and Development of Special Fund, Natural Science Foundation of Beijing Municipality.
Abstract (Originalsprache)
Purpose
To design and fabricate zirconia bars with porous surfaces using stereolithography and evaluate their surface characteristics and flexural strengths. Materials and Methods Five groups of zirconia bars (20 mm × 4 mm × 2 mm) with interconnected porous surfaces were designed and manufactured: (i) 400‐µm pore size and 50% porosity (D400‐P50 group), (ii) 400‐µm pore size and 30% porosity (D400‐P30 group), (iii) 200‐µm pore size and 50% porosity (D200‐P50 group), (iv) 200‐µm pore size and 30% porosity (D200‐P30 group), and (v) 100‐µm pore size and 30% porosity (D100‐P30 group). Zirconia bars without a porous surface (NP) were used as controls. The surface topographies and pore structures were investigated using scanning electron microscopy and three‐dimensional laser microscopy. The printed porosity was calculated using the Archimedes method. Fifteen specimens from each group were subjected to a three‐point bending test according to the ISO 6872:2015 standard. A Weibull analysis was performed, and the fractured surfaces were examined using scanning electron microscopy.
Results
Zirconia bars with porous surfaces were designed and successfully manufactured. The designed pore size, porosity, and shape of the printed pores were approximately achieved for all the porous surfaces. The flexural strength of the control group was significantly higher than those of the groups with porous surfaces ( p < 0.001). For the same porosity, groups with a pore size of 400 µm exhibited a lower flexural strength than the other groups ( p
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics, Peking University School and Hospital of Stomatology & National Center of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and…
- Foshan (Southern China) Institute for New Materials, Guangdong, China.
- Center of Digital Dentistry, Peking University School and Hospital of Stomatology, Beijing, China.
- National Engineering Laboratory for Digital and Material Technology of Stomatology, Research Center of Engineering and Technology for Digital Dentistry, Beijing, China.
ORCID-Profile: Quanquan Ma
Förderung
- Guangdong Basic and Applied Basic Research Foundation
- Capital Health Research and Development of Special Fund
- Natural Science Foundation of Beijing Municipality
Zitieren
APA
Ma, Q., Ding, Q., Zhang, L., Sun, Y., & Xie, Q. (2023). Surface Characteristics and Flexural Strength of Porous‐Surface Designed Zirconia Manufactured via Stereolithography. Journal of Prosthodontics, 32(4). https://doi.org/10.1111/jopr.13565
Vancouver
Ma Q, Ding Q, Zhang L, Sun Y, Xie Q. Surface Characteristics and Flexural Strength of Porous‐Surface Designed Zirconia Manufactured via Stereolithography. Journal of Prosthodontics. 2023;32(4). doi:10.1111/jopr.13565
BibTeX
@article{Ma2023,
author = {Ma, Quanquan and Ding, Qian and Zhang, Lei and Sun, Yuchun and Xie, Qiufei},
title = {Surface Characteristics and Flexural Strength of Porous‐Surface Designed Zirconia Manufactured via Stereolithography},
journal = {Journal of Prosthodontics},
year = {2023},
volume = {32},
number = {4},
doi = {10.1111/jopr.13565}
}
EUVIMED