Effect of Different Surface Treatments and Manufacturing Methods on the Shear Bond Strength of Repaired Resin‐Based Restorations
Journal of Esthetic and Restorative Dentistry · 2026-12 · 38 (12) · 2296-2305
DOI: 10.1111/jerd.70246 ↗At a glance
Journal article in Journal of Esthetic and Restorative Dentistry, published online on 2026-07-28. Written by Berkman Albayrak and 2 co-authors. Institution: Department of Prosthodontics, Bahçeşehir University School of Dental Medicine, Istanbul, Turkey. Major MEDLINE topics: Shear Strength, Dental Bonding, Composite Resins, Dental Restoration Repair. Cited 1 times so far (Crossref); 57 references. The full text is freely available (open access, CC BY 4.0).
Abstract (original language)
Objective
The aim of this in vitro study was to evaluate the effects of different surface treatments on the shear bond strength of repaired milled and 3D‐printed resin restorations. Materials and Methods A total of 84 resin specimens (8 mm diameter, 5 mm height) fabricated using two different methods such as milling (Grandio Disc) and 3D‐printing (Saremco Crowntec) were subjected to three surface treatments: silane (control), air abrasion + silane, and laser irradiation + silane. All specimens were subjected to thermocycling (5000 cycles each) before and after the repair protocol which was conducted with a flowable composite, and the shear bond strengths were measured. SEM images were obtained to evaluate the type of failures. Data were analyzed using IBM SPSS V23, and two‐way ANOVA analysis was used for comparisons between surface treatments and samples ( p < 0.05).
Results
Laser irradiation yielded the highest bond strength (7.61 ± 1.94 MPa), showing a statistically significant difference ( p = 0.001). The 3D‐printed resin group exhibited significantly higher bond strengths after all surface treatments compared to the milled group ( p = 0.028). Representative SEM observations revealed increased surface irregularity and fracture‐surface complexity in laser‐treated specimens.
Conclusion
Laser irradiation is an effective method for improving the bond strength in the repair of both milled and 3D‐printed resin restorations. Particularly, 3D‐printed resins showed superior repair bond strengths. Silane alone is insufficient; additional micromechanical surface treatments are required for reliable adhesion. Clinical Significance Mechanical complications can occur with milled and 3D‐printed resin restorations, which are increasingly used in indirect restorations, and intraoral repair protocols are becoming a crucial consideration. Determining the most appropriate repair protocol and surface treatment is crucial for the successful repair of these new‐generation resin restorations.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- Department of Prosthodontics, Bahçeşehir University School of Dental Medicine, Istanbul, Turkey.
- Department of Prosthodontics, Bezmialem University Faculty of Dentistry, Istanbul, Turkey.
- Department of Prosthodontics, Istanbul University Faculty of Dentistry, Istanbul, Turkey.
ORCID profiles: Berkman Albayrak
Cite
APA
Albayrak, B., Kocaer, S., & Saygılı, S. (2026). Effect of Different Surface Treatments and Manufacturing Methods on the Shear Bond Strength of Repaired Resin‐Based Restorations. Journal of Esthetic and Restorative Dentistry, 38(12), 2296-2305. https://doi.org/10.1111/jerd.70246
Vancouver
Albayrak B, Kocaer S, Saygılı S. Effect of Different Surface Treatments and Manufacturing Methods on the Shear Bond Strength of Repaired Resin‐Based Restorations. Journal of Esthetic and Restorative Dentistry. 2026;38(12):2296-2305. doi:10.1111/jerd.70246
BibTeX
@article{Albayrak2026,
author = {Albayrak, Berkman and Kocaer, Sarp and Saygılı, Sina},
title = {Effect of Different Surface Treatments and Manufacturing Methods on the Shear Bond Strength of Repaired Resin‐Based Restorations},
journal = {Journal of Esthetic and Restorative Dentistry},
year = {2026},
volume = {38},
number = {12},
pages = {2296--2305},
doi = {10.1111/jerd.70246}
}
EUVIMED