EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Occlusal Adjustment and Subsequent Repolishing on the Translucency Parameter, Contact Angle, and Flexural Strength of Different Types of Glazed Monolithic Zirconia

Kelli Nunes Monteiro, Rafaela Paschoalin Nigro, Stéphanie Soares Favero, Ranulfo Benedito de Paula Miranda iD, Estevam Augusto Bonfante iD, Paulo Francisco Cesar iD

Journal of Esthetic and Restorative Dentistry · 2026

DOI: 10.1111/jerd.70084 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, 2026. Verfasst von Kelli Nunes Monteiro und 5 weiteren Autor:innen. Beteiligte Einrichtung: Departamento de Biomateriais e Biologia Oral, Faculdade de Odontologia, Universidade de São Paulo, São Paulo, São Paulo, Brazil. Hauptthemen laut MEDLINE: Zirconium, Flexural Strength, Occlusal Adjustment, Dental Polishing. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Conselho Nacional de Desenvolvimento Científico e Tecnológico, Pró-Reitoria de Pesquisa, Universidade Federal de Minas Gerais.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

This study evaluated the effects of material and surface condition (glazed vs. polished after simulated occlusal adjustment) on translucency parameter, contact angle, and flexural strength of four monolithic zirconia. Materials and Methods Disk‐shaped specimens ( n = 80, Ø12 × 1 mm) were fabricated from four monolithic zirconia materials: Prettau 4 Anterior (PA), Lava Plus (LP), Cercon hT (hT), and Cercon xT (xT). All specimens were glazed; half underwent simulated occlusal adjustment followed by polishing. Translucency was measured with a spectrophotometer, contact angle with a goniometer, and flexural strength using a piston‐on‐three‐balls test. Data were analyzed via ANOVA.

Results

Translucency parameter values ranged from 3.9ᶜ (PA‐Polished) to 6.9ᵃ (xT‐Glazed), while contact angle (°) values ranged from 13.4ᵈ (hT‐Glazed) to 43.7ᵃ (xT‐Polished). Flexural strength (MPa) in the glazed condition was 410.4ᵇᶜ (PA), 577.5ᵇ (LP), 576.5ᵇ (hT), and 384.5ᵇᶜ (xT); under polishing, values were 333.1ᶜ (PA), 228.8ᶜ (LP), 856.0ᵃ (hT), and 287.1ᶜ (xT).

Conclusions

The xT group exhibited a higher translucency parameter compared to the LP and PA groups. Polishing increased the contact angle for all materials. Polishing subsequent to occlusal adjustment simulation preserved the flexural strength of two zirconia ceramics (PA and xT), resulted in a reduction in one (LP), and led to an increase in another (hT).

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumFlexural StrengthOcclusal AdjustmentDental PolishingDental MaterialsSurface PropertiesMaterials TestingHumansDental Stress Analysis

Stichwörter der Autor:innen

contact angleflexural strengthglazedmonolithicpolishingtranslucency parameterzirconia

Substanzen

Zirconiumzirconium oxideDental Materials

Autor:innen und Institutionen

  • Departamento de Biomateriais e Biologia Oral, Faculdade de Odontologia, Universidade de São Paulo, São Paulo, São Paulo, Brazil.
  • Departamento de Odontologia Restauradora, Faculdade de Odontologia, Universidade Federal de Minas Gerais, Belo Horizonte, Minas Gerais, Brazil.
  • Departamento de Prótese e Periodontia, Faculdade de Odontologia de Bauru, Universidade de São Paulo, Bauru, São Paulo, Brazil.

ORCID-Profile: Ranulfo Benedito de Paula Miranda, Estevam Augusto Bonfante, Paulo Francisco Cesar

Förderung

  • Conselho Nacional de Desenvolvimento Científico e Tecnológico
  • Pró-Reitoria de Pesquisa, Universidade Federal de Minas Gerais

Zitieren

APA

Monteiro, K. N., Nigro, R. P., Favero, S. S., de Paula Miranda, R. B., Bonfante, E. A., & Cesar, P. F. (2026). Effect of Occlusal Adjustment and Subsequent Repolishing on the Translucency Parameter, Contact Angle, and Flexural Strength of Different Types of Glazed Monolithic Zirconia. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.70084

Vancouver

Monteiro KN, Nigro RP, Favero SS, de Paula Miranda RB, Bonfante EA, Cesar PF. Effect of Occlusal Adjustment and Subsequent Repolishing on the Translucency Parameter, Contact Angle, and Flexural Strength of Different Types of Glazed Monolithic Zirconia. Journal of Esthetic and Restorative Dentistry. 2026. doi:10.1111/jerd.70084

BibTeX
@article{Monteiro2026,
  author = {Monteiro, Kelli Nunes and Nigro, Rafaela Paschoalin and Favero, Stéphanie Soares and de Paula Miranda, Ranulfo Benedito and Bonfante, Estevam Augusto and Cesar, Paulo Francisco},
  title = {Effect of Occlusal Adjustment and Subsequent Repolishing on the Translucency Parameter, Contact Angle, and Flexural Strength of Different Types of Glazed Monolithic Zirconia},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2026},
  doi = {10.1111/jerd.70084}
}
Kostenlos starten →