EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Characterization of Universal Composite Resin Filler Particles

Jorge Perdigão iD, Fernanda P Zatt, Guilherme C Lopes iD, Natália B Caon, Ruoqiong Chen

Journal of Esthetic and Restorative Dentistry · 2025-11 · 37 (11) · 2472-2480

DOI: 10.1111/jerd.70009 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, online erschienen am 27.07.2025. Verfasst von Jorge Perdigão und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Sciences, University of Minnesota School of Dentistry, Minneapolis, Minnesota, USA. Hauptthemen laut MEDLINE: Composite Resins. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

Characterize the morphology and distribution of filler particles of universal composite resins using Scanning Electron Microscopy, and calculate the residual filler mass fraction (filler wt%) of each composite resin with Thermogravimetric Analysis to compare the data with the respective filler wt% reported in the literature.

Methods

Seven universal composite resins (CRs) were analyzed in this study: Essentia Universal (EU), Filtek Easy Match (EM), Filtek Universal (FU), Omnichroma (OM), Simplishade (SS), TPH Spectra ST HV (ST), and Venus Diamond One (VO). Two classic multi‐shade CRs, Charisma Opal (CO) and Estelite Omega (EO) were used as controls. Two grams of each CR were dissolved in acetone, and the respective filler residue was dried and mounted on aluminum stubs. The specimens were sputter‐coated with Pt and observed under a Field‐Emission Scanning Electron Microscope to analyze the particle size and distribution at magnifications from ×5000 to ×80,000. For the Thermogravimetric Analysis, CR specimens were continuously weighed while heating up to 1000 o C to burn the organic contents and calculate the residual mass fraction of each material.

Results

Electron microscopy—OM showed a monomodal particle distribution of individual microparticles that contained nanoparticles. Sporadic agglomerations of microparticles were also observed for OM. EO, EU, FU, ST, VO, and EM displayed a bimodal filler distribution. The particles of CO and SS were organized under a trimodal distribution. There were similarities in particle shape and distribution for EM and FU, as well as for EO and OM. Classic particles of irregular shape larger than 2 μm were observed for CO, EU, ST, and VO. Clusters of nanoparticles up to 7.5 μm wide were observed for EM, FU, and SS. Thermogravimetric Analysis—The measured filler wt% was material specific. It ranged from 66.27% for EU to 78.28% for VO. The relative difference between the filler wt% measured for VO compared to the filler wt% reported in the literature was the smallest (−3.4%). EU resulted in the widest discrepancy (−18.2%).

Conclusion

The particle size and distribution varied for each composite resin, except for the pairs of materials EO/OM and EM/FU made by the same manufacturer. The filler wt% measured in this study was not in agreement with the description provided in the current literature for any of the CRs tested.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsMicroscopy, Electron, ScanningThermogravimetryParticle SizeMaterials Testing

Stichwörter der Autor:innen

dental materialsscanning electron microscopy (SEM)thermogravimetric analysis (TGA)universal composite resins

Substanzen

Composite Resins

Autor:innen und Institutionen

  • Department of Restorative Sciences, University of Minnesota School of Dentistry, Minneapolis, Minnesota, USA.
  • Department of Dentistry, Federal University of Santa Catarina, Florianópolis, Brazil.
  • Department of Chemistry, Federal University of Santa Catarina, Florianópolis, Brazil.
  • Department of Diagnostic and Biological Sciences, University of Minnesota School of Dentistry, Minneapolis, Minnesota, USA.

ORCID-Profile: Jorge Perdigão, Guilherme C Lopes

Zitieren

APA

Perdigão, J., Zatt, F. P., Lopes, G. C., Caon, N. B., & Chen, R. (2025). Characterization of Universal Composite Resin Filler Particles. Journal of Esthetic and Restorative Dentistry, 37(11), 2472-2480. https://doi.org/10.1111/jerd.70009

Vancouver

Perdigão J, Zatt FP, Lopes GC, Caon NB, Chen R. Characterization of Universal Composite Resin Filler Particles. Journal of Esthetic and Restorative Dentistry. 2025;37(11):2472-2480. doi:10.1111/jerd.70009

BibTeX
@article{Perdigo2025,
  author = {Perdigão, Jorge and Zatt, Fernanda P and Lopes, Guilherme C and Caon, Natália B and Chen, Ruoqiong},
  title = {Characterization of Universal Composite Resin Filler Particles},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2025},
  volume = {37},
  number = {11},
  pages = {2472--2480},
  doi = {10.1111/jerd.70009}
}
Kostenlos starten →