EUVIMEDOpdag EUVIMED
Open access · CC BY 4.0

Masking Ability of CAD ‐ CAM Materials at Different Thicknesses: A Study on Color, Translucency, and Infinite Optical Thickness

Bruno Arruda Mascaro iD, Maria Tejada-Casado, Renata Garcia Fonseca iD, Juan C Cardona, José Maurício Dos Santos Nunes Reis iD, María M Pérez iD

Journal of Esthetic and Restorative Dentistry · 2025-09 · 37 (9) · 2134-2143

DOI: 10.1111/jerd.13490 ↗

At a glance

Journal article in Journal of Esthetic and Restorative Dentistry, published online on 2025-05-27. Written by Bruno Arruda Mascaro and 5 co-authors. Institution: Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), School of Dentistry, São Paulo, Brazil. Major MEDLINE topics: Computer-Aided Design, Dental Porcelain, Prosthesis Coloring, Dental Materials. Cited 7 times so far (Crossref); 45 references. The full text is freely available (open access, CC BY 4.0). Funded by: Consejería de Universidad, Investigación e Innovación, Fondo Europeo d eDesarrollo Regional, São Paulo Research State Foundation (FAPESP).

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Objective

To evaluate the masking ability of different thicknesses of CAD‐CAM resin‐matrix and feldspar porcelain materials. Materials and Methods Specimens (Ø7.5 mm, thickness 0.5, 1.0, and 1.5 mm, n = 3/material) were fabricated from Lava Ultimate‐LU, Grandio Blocs‐GB, VITA Enamic‐VE, and VITA Mark II‐VM. Backgrounds were obtained from nine composite die shades (ND1‐ND9, IPS Natural Die Material). Spectral reflectance was measured for samples against a black background and each ND background. CIEDE2000 color differences (Δ E 00 ), relative translucency parameter differences (ΔRTP 00 ), and infinite optical thickness ( X ∞ ) were calculated. Δ E 00 data among materials were analyzed using Kruskal–Wallis and Mann–Whitney tests ( α = 0.05). Δ E 00 between thicknesses and ΔRTP 00 data were compared to perceptible and acceptable thresholds. Root mean square error (RMSE) and goodness‐of‐fit (GFC) were used as performance behavior of X ∞ .

Results

VM exhibited the lowest Δ E 00 ( p < 0.001) and ΔRTP 00 values across all tested conditions. Overall, LU and GB did not differ for 0.5 and 1.0 mm. Regardless of the background, when comparing 1.0–1.5 mm, acceptable Δ E 00 were observed, with only VM showing imperceptible values. Good spectral match and good comparative values of X ∞ were found for LU‐GB.

Conclusion

The masking effect depended on material and thickness, with VM and thicker samples demonstrating superior results. In general, the spectral behavior and values of infinite optical thickness differed among materials. Clinical Significance The masking ability of high‐translucency CAD‐CAM materials was influenced by composition, thickness, and the underlying tooth‐colored background. Materials with lower translucency and greater thickness are recommended for highly discolored teeth. Vita Mark II was the most suitable material for restorations on darkened substrates.

Subjects

MeSH terms (MEDLINE)

Computer-Aided DesignDental PorcelainProsthesis ColoringDental MaterialsComposite ResinsColorMaterials TestingDental Prosthesis DesignAluminum SilicatesHumansPotassium CompoundsCeramics

Author keywords

colordental materialsinfinite optical thicknessmasking abilitythickness color

Substances

Dental PorcelainfeldsparDental MaterialsAluminum SilicatesComposite ResinsVita Mark IIPotassium CompoundsVITA Enamic

Authors and institutions

  • Department of Dental Materials and Prosthodontics, São Paulo State University (UNESP), School of Dentistry, São Paulo, Brazil.
  • Department of Optics, Faculty of Science, Instituto de Investigación Biosanitaria ibs.GRANADA, University of Granada, Granada, Spain.

ORCID profiles: Bruno Arruda Mascaro, Renata Garcia Fonseca, José Maurício Dos Santos Nunes Reis, María M Pérez

Funding

  • Consejería de Universidad, Investigación e Innovación
  • Fondo Europeo d eDesarrollo Regional
  • São Paulo Research State Foundation (FAPESP)
  • Ministerio de Ciencia Innovación y Universidades
  • Fundação de Amparo à Pesquisa do Estado de São Paulo

Cite

APA

Mascaro, B. A., Tejada-Casado, M., Fonseca, R. G., Cardona, J. C., Dos Santos Nunes Reis, J. M., & Pérez, M. M. (2025). Masking Ability of CAD ‐ CAM Materials at Different Thicknesses: A Study on Color, Translucency, and Infinite Optical Thickness. Journal of Esthetic and Restorative Dentistry, 37(9), 2134-2143. https://doi.org/10.1111/jerd.13490

Vancouver

Mascaro BA, Tejada-Casado M, Fonseca RG, Cardona JC, Dos Santos Nunes Reis JM, Pérez MM. Masking Ability of CAD ‐ CAM Materials at Different Thicknesses: A Study on Color, Translucency, and Infinite Optical Thickness. Journal of Esthetic and Restorative Dentistry. 2025;37(9):2134-2143. doi:10.1111/jerd.13490

BibTeX
@article{Mascaro2025,
  author = {Mascaro, Bruno Arruda and Tejada-Casado, Maria and Fonseca, Renata Garcia and Cardona, Juan C and Dos Santos Nunes Reis, José Maurício and Pérez, María M},
  title = {Masking Ability of CAD ‐ CAM Materials at Different Thicknesses: A Study on Color, Translucency, and Infinite Optical Thickness},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2025},
  volume = {37},
  number = {9},
  pages = {2134--2143},
  doi = {10.1111/jerd.13490}
}
Start for free →