EUVIMEDPoznaj EUVIMED
Open access · CC BY-NC-ND 4.0

The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials

Jasmina Singh, Andrew B Cameron iD, Joanne Jung Eun Choi iD

Journal of Esthetic and Restorative Dentistry · 2025-07 · 37 (7) · 1930-1939

DOI: 10.1111/jerd.13475 ↗

At a glance

Journal article in Journal of Esthetic and Restorative Dentistry, published online on 2025-04-03. Written by Jasmina Singh and 2 co-authors. Institution: Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand. Major MEDLINE topics: Crowns, Dental Cements, Prosthesis Coloring. Cited 7 times so far (Crossref); 29 references. The full text is freely available (open access, CC BY-NC-ND 4.0). Funded by: New Zealand Dental Research Foundation.

AbstraktSubjectsDane bibliograficzneCiteRelated studies

Abstract (original language)

Objectives

To investigate the effect of cement shade and printing parameters on the optical properties of additively manufactured (AM) permanent crown materials.

Methods

Two AM crown materials (Bego VarseoSmile Crown Plus and Formlabs Permanent Crown) and one conventional milled material were tested ( n = 560). Dimensions for each specimen measured 10 × 10 mm and were categorized by thickness (1 and 2 mm). AM materials were additively manufactured (3D‐printed) at three orientations: 0°, 45° and 90°. Specimens were cemented with four shades of dual‐cure cement: light, neutral, warm, and translucent. Color change (Δ E ) and translucency parameter (TP) measurements were calculated utilizing a spectrophotometer, VITA EasyShade V. Data was analyzed with a two‐ way ANOVA and Tukey's post hoc tests.

Results

Neutral cement shade exhibited the lowest Δ E overall (2.30 ± 0.43). Translucent cement shade exhibited the least color difference between materials. Milled materials generally exhibited higher Δ E (5.57 ± 0.26–7.17 ± 0.33) than AM materials. Material thickness significantly affected the Δ E across all shades of cement ( p < 0.05). 45° print orientation for 2 mm thick specimens exhibited the greatest clinically acceptable Δ E .

Conclusion

Cement shade may cause clinically unacceptable color changes based on material choice and 3D‐printing parameters. Clinicians providing permanent AM crowns must consider the impact of cement shade and printing parameters on aesthetic outcomes.

Subjects

MeSH terms (MEDLINE)

CrownsDental CementsProsthesis ColoringColorMaterials TestingPrinting, Three-DimensionalHumansSpectrophotometryDental Prosthesis Design

Author keywords

3D printingadditive manufacturingcement shadecolor changedental cementoptical propertiestranslucency

Substances

Dental Cements

Authors and institutions

  • Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand.
  • School of Medicine and Dentistry, Griffith University, Gold Coast, Australia.

ORCID profiles: Andrew B Cameron, Joanne Jung Eun Choi

Funding

  • New Zealand Dental Research Foundation

Cite

APA

Singh, J., Cameron, A. B., & Choi, J. J. E. (2025). The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials. Journal of Esthetic and Restorative Dentistry, 37(7), 1930-1939. https://doi.org/10.1111/jerd.13475

Vancouver

Singh J, Cameron AB, Choi JJE. The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials. Journal of Esthetic and Restorative Dentistry. 2025;37(7):1930-1939. doi:10.1111/jerd.13475

BibTeX
@article{Singh2025,
  author = {Singh, Jasmina and Cameron, Andrew B and Choi, Joanne Jung Eun},
  title = {The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2025},
  volume = {37},
  number = {7},
  pages = {1930--1939},
  doi = {10.1111/jerd.13475}
}
Start for free →