The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials
Journal of Esthetic and Restorative Dentistry · 2025-07 · 37 (7) · 1930-1939
DOI: 10.1111/jerd.13475 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, online erschienen am 03.04.2025. Verfasst von Jasmina Singh und 2 weiteren Autor:innen. Beteiligte Einrichtung: Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand. Hauptthemen laut MEDLINE: Crowns, Dental Cements, Prosthesis Coloring. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: New Zealand Dental Research Foundation.
Abstract (Originalsprache)
Objectives
To investigate the effect of cement shade and printing parameters on the optical properties of additively manufactured (AM) permanent crown materials.
Methods
Two AM crown materials (Bego VarseoSmile Crown Plus and Formlabs Permanent Crown) and one conventional milled material were tested ( n = 560). Dimensions for each specimen measured 10 × 10 mm and were categorized by thickness (1 and 2 mm). AM materials were additively manufactured (3D‐printed) at three orientations: 0°, 45° and 90°. Specimens were cemented with four shades of dual‐cure cement: light, neutral, warm, and translucent. Color change (Δ E ) and translucency parameter (TP) measurements were calculated utilizing a spectrophotometer, VITA EasyShade V. Data was analyzed with a two‐ way ANOVA and Tukey's post hoc tests.
Results
Neutral cement shade exhibited the lowest Δ E overall (2.30 ± 0.43). Translucent cement shade exhibited the least color difference between materials. Milled materials generally exhibited higher Δ E (5.57 ± 0.26–7.17 ± 0.33) than AM materials. Material thickness significantly affected the Δ E across all shades of cement ( p < 0.05). 45° print orientation for 2 mm thick specimens exhibited the greatest clinically acceptable Δ E .
Conclusion
Cement shade may cause clinically unacceptable color changes based on material choice and 3D‐printing parameters. Clinicians providing permanent AM crowns must consider the impact of cement shade and printing parameters on aesthetic outcomes.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Sir John Walsh Research Institute, Faculty of Dentistry, University of Otago, Dunedin, New Zealand.
- School of Medicine and Dentistry, Griffith University, Gold Coast, Australia.
ORCID-Profile: Andrew B Cameron, Joanne Jung Eun Choi
Förderung
- New Zealand Dental Research Foundation
Zitieren
APA
Singh, J., Cameron, A. B., & Choi, J. J. E. (2025). The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials. Journal of Esthetic and Restorative Dentistry, 37(7), 1930-1939. https://doi.org/10.1111/jerd.13475
Vancouver
Singh J, Cameron AB, Choi JJE. The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials. Journal of Esthetic and Restorative Dentistry. 2025;37(7):1930-1939. doi:10.1111/jerd.13475
BibTeX
@article{Singh2025,
author = {Singh, Jasmina and Cameron, Andrew B and Choi, Joanne Jung Eun},
title = {The Effect of Cement Shade on the Optical Properties of Additively Manufactured Permanent Crown Materials},
journal = {Journal of Esthetic and Restorative Dentistry},
year = {2025},
volume = {37},
number = {7},
pages = {1930--1939},
doi = {10.1111/jerd.13475}
}
EUVIMED