Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns
Journal of Esthetic and Restorative Dentistry · 2024-01 · 36 (1) · 94-106
DOI: 10.1111/jerd.13169 ↗At a glance
Journal article in Journal of Esthetic and Restorative Dentistry, 2024-01. Written by F A Spitznagel and 7 co-authors. Institution: Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Düsseldorf, Germany. Major MEDLINE topics: Dental Porcelain, Crowns, Acrylic Resins, Composite Resins. Cited 20 times so far (Crossref); 63 references. The full text is freely available (open access, CC BY-NC-ND 4.0). Funded by: NIDCR NIH HHS, National Institute of Dental and Craniofacial Research.
Abstract (original language)
Objective
To analyze the influence of restoration design (partial‐coverage restoration vs. crown) and ceramic layer thickness on the performance and failure loads of CAD/CAM‐fabricated lithium disilicate (LDS) reconstructions on molars after fatigue. Materials and Methods Seventy‐two posterior monolithic CAD/CAM‐fabricated LDS restorations (IPS e.max CAD, Ivoclar Vivadent) with different occlusal/buccal ceramic layer thicknesses (1.5/0.8, 1.0/0.6, and 0.5/0.4 mm) and restoration designs (PCR: non‐retentive full‐veneer/partial‐coverage restoration, C: crown,) were investigated and divided into six groups ( n = 12, test: PCR‐1.5, PCR‐1.0, PCR‐0.5; control: C‐1.5, C‐1.0, C‐0.5). LDS restorations were adhesively bonded (Variolink Esthetic DC, Ivoclar Vivadent) to dentin‐analogue composite dies (Z100, 3M ESPE). All specimens were subjected to thermomechanical loading (1.2 million cycles, 49 N, 1.6 Hz, 5–55°C) and exposed to single load to failure testing. Failure analysis was performed with light and scanning electron microscopies. Data were statistically analyzed using ANOVA, Tukey‐Test, and t ‐test ( p < 0.05).
Results
Eight crown samples (C‐0.5) and one PCR specimen (PCR‐0.5) revealed cracks after fatigue, resulting in an overall success rate of 87.5% (crowns: 75%, PCRs: 96.88%). Direct comparisons of PCRs versus crowns for thicknesses of 0.5 mm ( p < 0.001) and 1.0 mm ( p = 0.004) were significant and in favor of PCRs. Minimally invasive PCRs (0.5 and 1.0 mm) outperformed crowns with the identical ceramic thickness. No difference was detected ( p = 0.276) between thickness 1.5 mm PCRs and crowns.
Conclusions
Minimally invasive monolithic CAD/CAM‐fabricated posterior LDS PCRs (0.5 and 1.0 mm) resulted in superior failure load values compared to minimally invasive crowns. Minimally invasive crowns (0.5 mm) are prone to cracks after fatigue. Clinical Significance Minimally invasive CAD/CAM‐fabricated LDS PCR restorations with a non‐retentive preparation design should be considered over single crowns for molar rehabilitation.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Düsseldorf, Germany.
- Department of Preventive and Restorative Sciences, Penn Dental Medicine, University of Pennsylvania, Philadelphia, Pennsylvania, USA.
- Institute of Systems Neuroscience, Medical Faculty, Heinrich-Heine-University Düsseldorf, Düsseldorf, Germany.
- Institute of Neuroscience and Medicine, Brain and Behavior (INM-7), Research Center Jülich, Jülich, Germany.
ORCID profiles: F A Spitznagel, L S Prott, M B Blatz, Y Zhang, R Langner, P C Gierthmuehlen
Funding
- NIDCR NIH HHS
- National Institute of Dental and Craniofacial Research
Cite
APA
Spitznagel, F. A., Prott, L. S., Hoppe, J. S., Manitckaia, T., Blatz, M. B., Zhang, Y., Langner, R., & Gierthmuehlen, P. C. (2024). Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13169
Vancouver
Spitznagel FA, Prott LS, Hoppe JS, Manitckaia T, Blatz MB, Zhang Y, et al. Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns. Journal of Esthetic and Restorative Dentistry. 2024. doi:10.1111/jerd.13169
BibTeX
@article{Spitznagel2024,
author = {Spitznagel, F A and Prott, L S and Hoppe, J S and Manitckaia, T and Blatz, M B and Zhang, Y and Langner, R and Gierthmuehlen, P C},
title = {Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns},
journal = {Journal of Esthetic and Restorative Dentistry},
year = {2024},
doi = {10.1111/jerd.13169}
}
EUVIMED