EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns

F A Spitznagel iD, L S Prott iD, J S Hoppe, T Manitckaia, M B Blatz iD, Y Zhang iD, R Langner iD, P C Gierthmuehlen iD

Journal of Esthetic and Restorative Dentistry · 2024

DOI: 10.1111/jerd.13169 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Esthetic and Restorative Dentistry, 2024. Verfasst von F A Spitznagel und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Düsseldorf, Germany. Hauptthemen laut MEDLINE: Dental Porcelain, Crowns, Acrylic Resins, Composite Resins. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 63 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: NIDCR NIH HHS, National Institute of Dental and Craniofacial Research.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

To analyze the influence of restoration design (partial‐coverage restoration vs. crown) and ceramic layer thickness on the performance and failure loads of CAD/CAM‐fabricated lithium disilicate (LDS) reconstructions on molars after fatigue. Materials and Methods Seventy‐two posterior monolithic CAD/CAM‐fabricated LDS restorations (IPS e.max CAD, Ivoclar Vivadent) with different occlusal/buccal ceramic layer thicknesses (1.5/0.8, 1.0/0.6, and 0.5/0.4 mm) and restoration designs (PCR: non‐retentive full‐veneer/partial‐coverage restoration, C: crown,) were investigated and divided into six groups ( n = 12, test: PCR‐1.5, PCR‐1.0, PCR‐0.5; control: C‐1.5, C‐1.0, C‐0.5). LDS restorations were adhesively bonded (Variolink Esthetic DC, Ivoclar Vivadent) to dentin‐analogue composite dies (Z100, 3M ESPE). All specimens were subjected to thermomechanical loading (1.2 million cycles, 49 N, 1.6 Hz, 5–55°C) and exposed to single load to failure testing. Failure analysis was performed with light and scanning electron microscopies. Data were statistically analyzed using ANOVA, Tukey‐Test, and t ‐test ( p < 0.05).

Results

Eight crown samples (C‐0.5) and one PCR specimen (PCR‐0.5) revealed cracks after fatigue, resulting in an overall success rate of 87.5% (crowns: 75%, PCRs: 96.88%). Direct comparisons of PCRs versus crowns for thicknesses of 0.5 mm ( p < 0.001) and 1.0 mm ( p = 0.004) were significant and in favor of PCRs. Minimally invasive PCRs (0.5 and 1.0 mm) outperformed crowns with the identical ceramic thickness. No difference was detected ( p = 0.276) between thickness 1.5 mm PCRs and crowns.

Conclusions

Minimally invasive monolithic CAD/CAM‐fabricated posterior LDS PCRs (0.5 and 1.0 mm) resulted in superior failure load values compared to minimally invasive crowns. Minimally invasive crowns (0.5 mm) are prone to cracks after fatigue. Clinical Significance Minimally invasive CAD/CAM‐fabricated LDS PCR restorations with a non‐retentive preparation design should be considered over single crowns for molar rehabilitation.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PorcelainCrownsAcrylic ResinsComposite ResinsPolyurethanesHumansCeramicsComputer-Aided DesignFatigueMaterials TestingDental Restoration FailureDental Stress Analysis

Stichwörter der Autor:innen

ceramicscomputer-aided designfatiguefull-veneerpartial-coverage restoration

Substanzen

lithia disilicateVivadentDental PorcelainAcrylic ResinsComposite ResinsPolyurethanes

Autor:innen und Institutionen

  • Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Düsseldorf, Germany.
  • Department of Preventive and Restorative Sciences, Penn Dental Medicine, University of Pennsylvania, Philadelphia, Pennsylvania, USA.
  • Institute of Systems Neuroscience, Medical Faculty, Heinrich-Heine-University Düsseldorf, Düsseldorf, Germany.
  • Institute of Neuroscience and Medicine, Brain and Behavior (INM-7), Research Center Jülich, Jülich, Germany.

ORCID-Profile: F A Spitznagel, L S Prott, M B Blatz, Y Zhang, R Langner, P C Gierthmuehlen

Förderung

  • NIDCR NIH HHS
  • National Institute of Dental and Craniofacial Research

Zitieren

APA

Spitznagel, F. A., Prott, L. S., Hoppe, J. S., Manitckaia, T., Blatz, M. B., Zhang, Y., Langner, R., & Gierthmuehlen, P. C. (2024). Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13169

Vancouver

Spitznagel FA, Prott LS, Hoppe JS, Manitckaia T, Blatz MB, Zhang Y, et al. Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns. Journal of Esthetic and Restorative Dentistry. 2024. doi:10.1111/jerd.13169

BibTeX
@article{Spitznagel2024,
  author = {Spitznagel, F A and Prott, L S and Hoppe, J S and Manitckaia, T and Blatz, M B and Zhang, Y and Langner, R and Gierthmuehlen, P C},
  title = {Minimally invasive CAD / CAM lithium disilicate partial‐coverage restorations show superior in‐vitro fatigue performance than single crowns},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2024},
  doi = {10.1111/jerd.13169}
}
Kostenlos starten →