EUVIMEDObjevte EUVIMED
Open access · CC BY 4.0

Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics

Evangelos Ximinis, Dimitrios Dionysopoulos iD, Constantinos Papadopoulos, Alexandros Tournavitis, Avraam Konstantinidis, Olga Naka iD

Journal of Esthetic and Restorative Dentistry · 2023

DOI: 10.1111/jerd.13043 ↗

At a glance

Journal article in Journal of Esthetic and Restorative Dentistry, 2023. Written by Evangelos Ximinis and 5 co-authors. Institution: Department of Prosthodontics, Faculty of Dentistry, School of Health Sciences, Aristotle University of Thessaloniki, Thessaloniki, Greece. Major MEDLINE topics: Dental Porcelain, Toothbrushing. Cited 9 times so far (Crossref); 41 references. The full text is freely available (open access, CC BY 4.0).

AbstraktSubjectsBibliografické údajeCiteRelated studies

Abstract (original language)

Purpose

The purpose was to investigate the alterations in surface properties of different resin‐matrix CAD/CAM ceramics following tooth brushing simulation (TBS) and compare them with a direct resin composite and a glass ceramic CAD/CAM material. Materials and methods Four resin‐based CAD/CAM restoratives (Brilliant Crios—BR, Lava™ Ultimate—LV, Grandio Blocs—GR and Shofu Block HC—SH), a leucite‐reinforced glass ceramic (IPS Empress® CAD—EC) and a resin composite (Filtek™ Z250—FZ) for direct restorations were tested. In particular, surface loss, hardness, roughness and morphology were investigated utilizing confocal microscopy, scanning electron microscopy and nanoindentation tester. TBS was conducted for 4 × 15 min on the surface of the samples and then the changes in their surface properties were evaluated.

Results

After TBS, all the experimental groups exhibited surface loss to different extent. FZ and BR presented the highest surface loss, while EC and GR the lowest ( p < 0.05). Regarding surface roughness, all the tested materials exhibited increase after TBS ( p < 0.05), except LV ( p = 0.099). EC presented the lowest Sa values, while FZ and BR the highest ( p < 0.05). Changes in surface morphology were in compliance with the results of surface roughness and also surface hardness was correlated with surface loss.

Conclusions

The tested resin‐matrix CAD/CAM ceramic restorative materials showed a competent behavior against abrasive forces applied during TBS. Surface loss and roughness changes were material dependent and superior compared to a resin composite for direct restorations, while in comparison with a leucite‐reinforced glass ceramic exhibited inferior properties. Clinical significance Tooth brushing affected differently the surface of the tested restorative materials. However, the abrasive wear that was induced was negligible. Clinical studies are necessary to ascertain if there is clinical significance of these surface alterations that may demand repair of such restorations.

Subjects

MeSH terms (MEDLINE)

Dental PorcelainToothbrushingCeramicsComposite ResinsDental MaterialsComputer-Aided DesignSurface PropertiesMaterials TestingAluminum Silicates

Author keywords

leucite-reinforced glass ceramicsresin-matrix CAD/CAM ceramicssurface losssurface roughnesstooth brushing simulation

Substances

Dental PorcelainComposite ResinsDental MaterialsleuciteAluminum Silicates

Authors and institutions

  • Department of Prosthodontics, Faculty of Dentistry, School of Health Sciences, Aristotle University of Thessaloniki, Thessaloniki, Greece.
  • Department of Operative Dentistry, School of Health Sciences, Faculty of Dentistry, Aristotle University of Thessaloniki, Thessaloniki, Greece.
  • Department of Civil Engineering, Division of Structural Engineering, Faculty of Engineering, Aristotle University of Thessaloniki, Thessaloniki, Greece.

ORCID profiles: Dimitrios Dionysopoulos, Olga Naka

Cite

APA

Ximinis, E., Dionysopoulos, D., Papadopoulos, C., Tournavitis, A., Konstantinidis, A., & Naka, O. (2023). Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics. Journal of Esthetic and Restorative Dentistry. https://doi.org/10.1111/jerd.13043

Vancouver

Ximinis E, Dionysopoulos D, Papadopoulos C, Tournavitis A, Konstantinidis A, Naka O. Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics. Journal of Esthetic and Restorative Dentistry. 2023. doi:10.1111/jerd.13043

BibTeX
@article{Ximinis2023,
  author = {Ximinis, Evangelos and Dionysopoulos, Dimitrios and Papadopoulos, Constantinos and Tournavitis, Alexandros and Konstantinidis, Avraam and Naka, Olga},
  title = {Effect of tooth brushing simulation on the surface properties of various resin‐matrix computer‐aided design/computer‐aided manufacturing ceramics},
  journal = {Journal of Esthetic and Restorative Dentistry},
  year = {2023},
  doi = {10.1111/jerd.13043}
}
Start for free →