EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Energy‐Efficient Microwave Sintering of Binder‐Jetted Alumina

Bashu Aman, Sampada Acharya, Alex Gourley, Tania Slawecki, Dinesh Agrawal, Pranjali D. Muley, B. Reeja‐Jayan

Journal of the American Ceramic Society · 2026-04 · 109 (4)

DOI: 10.1111/jace.70691 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of the American Ceramic Society, online erschienen am 26.03.2026. Verfasst von Bashu Aman und 6 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 61 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Microwave (MW) sintering offers an energy‐efficient approach for densifying Al 2 O 3 ceramics. However, its adoption for ceramics 3D‐printed via binder‐jetting remains limited due to uneven heating, particularly in complex geometries. SiC susceptors improve thermal uniformity, but induce charge concentration and local hotspots, requiring careful control. Here, multiphysics models are combined with experiments to control hotspots and uniformly sinter binder‐jetted Al 2 O 3 using 2.45 GHz MWs. We developed electromagnetic wave‐heat transfer models to investigate how SiC susceptor configurations influence Al 2 O 3 heating. Simulations revealed that hexagonal configuration minimized sample temperature non‐uniformity (∼20°C), while square configuration suppressed localized hotspots. With reduced overheating, we experimentally sintered binder‐jetted blocks across 1300°C–1500°C, achieving ∼75%–86% relative density with microstructures and α‐alumina phases similar to conventional sintering, while at 1500°C shrinkage (∼65%–66%) was also comparable, reducing hold time from 6 h to 7.5 min. Extending to complex geometries, we applied the optimized process to evenly heat and sinter binder‐jetted spur gears, widely used in aerospace, achieving mechanical strength (∼54 N tooth‐failure load and ∼24.5 MPa maximum bending stress) comparable to its conventional counterpart (∼50 N tooth‐failure load in our study and ∼24.5 MPa bending stress reported in prior studies). Unlike previous MW sintering studies, the results enable uniform, hotspot‐controlled MW sintering of 3D‐printed ceramics. The ∼48x faster processing and ∼96% lower energy use than conventional, reinforces it as a scalable, electrified route for high‐throughput, decarbonized ceramic manufacturing.

Zitieren

APA

Aman, B., Acharya, S., Gourley, A., Slawecki, T., Agrawal, D., Muley, P. D., & Reeja‐Jayan, B. (2026). Energy‐Efficient Microwave Sintering of Binder‐Jetted Alumina. Journal of the American Ceramic Society, 109(4). https://doi.org/10.1111/jace.70691

Vancouver

Aman B, Acharya S, Gourley A, Slawecki T, Agrawal D, Muley PD, et al. Energy‐Efficient Microwave Sintering of Binder‐Jetted Alumina. Journal of the American Ceramic Society. 2026;109(4). doi:10.1111/jace.70691

BibTeX
@article{Aman2026,
  author = {Aman, Bashu and Acharya, Sampada and Gourley, Alex and Slawecki, Tania and Agrawal, Dinesh and Muley, Pranjali D. and Reeja‐Jayan, B.},
  title = {Energy‐Efficient Microwave Sintering of Binder‐Jetted Alumina},
  journal = {Journal of the American Ceramic Society},
  year = {2026},
  volume = {109},
  number = {4},
  doi = {10.1111/jace.70691}
}
Kostenlos starten →