EUVIMEDEUVIMED entdecken
Crossref

Multi‐material additive manufacturing of functionally graded ultra‐high temperature ceramics via active in‐line mixing

Saqlain Zaman, Joseph Munoz, Mathew Ivill, Tucker Moore, Clifford Hubbard, Yirong Lin, Lionel Vargas‐Gonzalez, Nicholas Ku

International Journal of Applied Ceramic Technology · 2026-02 · 23 (1)

DOI: 10.1111/ijac.70130 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Applied Ceramic Technology, online erschienen am 23.12.2025. Verfasst von Saqlain Zaman und 7 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 49 Literaturangaben. Gefördert von: DEVCOM Army Research Laboratory.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ultra‐high temperature ceramics (UHTCs) are valued for their exceptional mechanical, thermal properties, and oxidation resistance. Among UHTCs, zirconium diboride (ZrB 2 ) reinforced with silicon carbide (SiC) has emerged as a promising candidate for extreme environment applications due to its exceptional combination of high melting point, thermal conductivity, oxidation resistance, and mechanical strength. While most UHTC research has focused on monolithic structures, functionally graded materials offer a novel pathway to further enhance performance by gradually transitioning composition between constituent materials. In this work, a custom‐built direct ink writing (DIW) additive manufacturing system with active in‐line mixing was implemented to fabricate functionally graded ZrB 2 –SiC ceramics. Rheologically optimized aqueous suspensions of ZrB 2 and SiC were formulated with matched viscosity profiles for co‐extrusion. The system enabled continuous and discrete gradient structures by varying composition in real time during printing. Post‐processing involved binder burnout and hot pressing to achieve densification. The graded samples exhibited high relative density (∼93%) and 25% increase in hardness from the ZrB 2 ‐rich to SiC‐rich regions. The elastic modulus in the gradient samples exceeded 517 GPa, which is 2% higher than monolithic ZrB 2 and 78% higher than monolithic SiC. These findings demonstrate the viability of DIW for fabricating dense, graded UHTCs with tunable mechanical properties.

Förderung

  • DEVCOM Army Research Laboratory

Zitieren

APA

Zaman, S., Munoz, J., Ivill, M., Moore, T., Hubbard, C., Lin, Y., Vargas‐Gonzalez, L., & Ku, N. (2026). Multi‐material additive manufacturing of functionally graded ultra‐high temperature ceramics via active in‐line mixing. International Journal of Applied Ceramic Technology, 23(1). https://doi.org/10.1111/ijac.70130

Vancouver

Zaman S, Munoz J, Ivill M, Moore T, Hubbard C, Lin Y, et al. Multi‐material additive manufacturing of functionally graded ultra‐high temperature ceramics via active in‐line mixing. International Journal of Applied Ceramic Technology. 2026;23(1). doi:10.1111/ijac.70130

BibTeX
@article{Zaman2026,
  author = {Zaman, Saqlain and Munoz, Joseph and Ivill, Mathew and Moore, Tucker and Hubbard, Clifford and Lin, Yirong and Vargas‐Gonzalez, Lionel and Ku, Nicholas},
  title = {Multi‐material additive manufacturing of functionally graded ultra‐high temperature ceramics via active in‐line mixing},
  journal = {International Journal of Applied Ceramic Technology},
  year = {2026},
  volume = {23},
  number = {1},
  doi = {10.1111/ijac.70130}
}
Kostenlos starten →