Dentine thickness in maxillary fused molars depends on the fusion type: An ex vivo micro‐computed tomography study
International Endodontic Journal · 2023
DOI: 10.1111/iej.13891 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Endodontic Journal, 2023. Verfasst von Cangül Keskin und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Endodontics, Faculty of Dentistry, Ondokuz Mayis University, Samsun, Turkey. Hauptthemen laut MEDLINE: Tooth Root, Molar. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 30 Literaturangaben. Gefördert von: Samsun Ondokuz Mayis University Research Fund.
Abstract (Originalsprache)
Aim
The present study aimed to determine and compare the dentine thickness around the root canals of maxillary molars with fusion using micro‐computed tomography (micro‐CT). Methodology A total of 120 fused maxillary molars having more than a single canal with distinct canal orifices near the cementoenamel junction were selected from a pool of extracted maxillary molars, which were scanned on a micro‐CT device (SkyScan 1172, Bruker‐microCT). The minimum dentine thickness around the root canals in furcal direction was measured using CTAn software (v.1.18.8 Bruker‐microCT) at each millimetre. The specimens were grouped according to their fusion type, and dentine thickness around the canals was compared. The data were statistically analysed using anova and post hoc Tukey–Kramer tests following an assessment of the normality of their distribution with the Kolmogorov–Smirnov test ( p < .05).
Results
Dentine thickness showed a statistically significant decrease at 2 mm apical to the orifice level irrespective of fusion type. The minimum dentine thickness values were detected around the second mesiobuccal canal as 0.30 mm at 6 mm below orifice. Dentine thickness around the mesiobuccal canal was significantly greater in fusion type 1 than those of types 2 and 3 ( p < .05), while those of distobuccal and palatal canals were significantly thinner in type 3 fusion compared with type 1 or 6 ( p Dentine thickness showed a statistically significant decrease at 2 mm apical to the orifice level irrespective of fusion type. The minimum dentine thickness values were detected around the second mesiobuccal canal as 0.30 mm at 6 mm below orifice. Dentine thickness around the mesiobuccal canal was significantly greater in fusion type 1 than those of types 2 and 3 ( Conclusion Minimum dentine thickness values at the danger zone of distobuccal and palatal canals change according to the fusion type in fused maxillary second molars.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Endodontics, Faculty of Dentistry, Ondokuz Mayis University, Samsun, Turkey.
ORCID-Profile: Cangül Keskin, Ali Keleş
Förderung
- Samsun Ondokuz Mayis University Research Fund
Zitieren
APA
Keskin, C., Toplu, D., & Keleş, A. (2023). Dentine thickness in maxillary fused molars depends on the fusion type: An ex vivo micro‐computed tomography study. International Endodontic Journal. https://doi.org/10.1111/iej.13891
Vancouver
Keskin C, Toplu D, Keleş A. Dentine thickness in maxillary fused molars depends on the fusion type: An ex vivo micro‐computed tomography study. International Endodontic Journal. 2023. doi:10.1111/iej.13891
BibTeX
@article{Keskin2023,
author = {Keskin, Cangül and Toplu, Defne and Keleş, Ali},
title = {Dentine thickness in maxillary fused molars depends on the fusion type: An ex vivo micro‐computed tomography study},
journal = {International Endodontic Journal},
year = {2023},
doi = {10.1111/iej.13891}
}
EUVIMED