EUVIMEDEUVIMED entdecken
Crossref

An Iterative Method of Modeling Pump‐Treat‐Inject System with “Partial Treatment”

Jim Zhang iD, Yiding Zhang iD, Franklin W Schwartz, Massoud Karimi

Groundwater · 2024

DOI: 10.1111/gwat.13377 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Groundwater, 2024. Verfasst von Jim Zhang und 3 weiteren Autor:innen. Beteiligte Einrichtung: Geosyntec, 924 Anacapa Street, Suite 4A, Santa Barbara, CA, 93101. Hauptthemen laut MEDLINE: Groundwater, Models, Theoretical, Water Pollutants, Chemical. Die Arbeit nennt 18 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Pump‐and‐treat technologies are widely used in groundwater remediation and site cleanup. Such technologies involve pumping contaminated groundwater to the surface for treatment. Following treatment, the water is often reinjected back into the aquifer (referred to as pump‐treat‐inject or PTI) for potential reuse. The treatment system is often designed to remove dissolved‐phase contaminants in groundwater such that water meets applicable cleanup standards (herein referred to as “full treatment”). However, in some cases, the treatment system may not effectively reduce the dissolved‐phase concentrations (herein referred to as “partial treatment”) for some of the contaminants present in groundwater. Modeling PTI under partial treatment conditions is challenging because contaminant concentrations in injected water depend on the pumped water concentrations and the system treatment efficiency. Essentially, the injected water concentration (a transport model input) is unknown prior to transport simulation. This study presents a novel iterative approach to modeling PTI under partial treatment scenarios, where the injected water concentration is linked to the modeled pumped water concentration. The method was developed for a complicated three‐dimensional (3D) flow and transport modeling study conducted for a confidential remediation site where PTI with partial treatment was applied. However, due to the complexity of the 3D model and the confidential information of the site, a simple two‐dimensional (2D) numerical model is presented to demonstrate the iterative method. The 2D model test runs and the 3D model application in a remediation site showed that the iterative simulation results quickly converged to a viable final solution.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

GroundwaterModels, TheoreticalWater Pollutants, ChemicalWater MovementsEnvironmental Restoration and RemediationEnvironmental MonitoringWater Purification

Substanzen

Water Pollutants, Chemical

Autor:innen und Institutionen

  • Geosyntec, 924 Anacapa Street, Suite 4A, Santa Barbara, CA, 93101.
  • School of Earth Sciences, The Ohio State University, 125 South Oval Mall, Columbus, OH, 43210.
  • Geoenvirosearch, 3298 Governor Drive, #22101, San Diego, CA, 92122.

ORCID-Profile: Jim Zhang, Yiding Zhang

Zitieren

APA

Zhang, J., Zhang, Y., Schwartz, F. W., & Karimi, M. (2024). An Iterative Method of Modeling Pump‐Treat‐Inject System with “Partial Treatment”. Groundwater. https://doi.org/10.1111/gwat.13377

Vancouver

Zhang J, Zhang Y, Schwartz FW, Karimi M. An Iterative Method of Modeling Pump‐Treat‐Inject System with “Partial Treatment”. Groundwater. 2024. doi:10.1111/gwat.13377

BibTeX
@article{Zhang2024,
  author = {Zhang, Jim and Zhang, Yiding and Schwartz, Franklin W and Karimi, Massoud},
  title = {An Iterative Method of Modeling Pump‐Treat‐Inject System with “Partial Treatment”},
  journal = {Groundwater},
  year = {2024},
  doi = {10.1111/gwat.13377}
}
Kostenlos starten →