Physicochemical characterization of etch‐and‐rinse adhesive system doped with catechin‐loaded polymeric microparticles
European Journal of Oral Sciences · 2026-06 · 134 (3)
DOI: 10.1111/eos.70087 ↗At a glance
Journal article in European Journal of Oral Sciences, published online on 2026-03-12. Written by Jiovanne Rabelo Neri and 6 co-authors. Institution: Graduate School of Dentistry, University Center Christus, Fortaleza, Ceará, Brazil. Major MEDLINE topics: Catechin, Lactic Acid, Polyglycolic Acid, Dentin-Bonding Agents. Cited 1 times so far (Crossref); 45 references. The full text is freely available (open access, CC BY 4.0). Funded by: Conselho Nacional de Desenvolvimento Científico e Tecnológico.
Abstract (original language)
This study evaluated the incorporation of epigallocatechin‐3‐gallate (EGCG)‐loaded poly(lactide‐ co ‐glycolide) (PLGA) microparticles into a two‐step etch‐and‐rinse adhesive and their effects on physicochemical properties and EGCG release. EGCG was added to Single Bond 2 either directly (0.01% and 0.1% w/w) or encapsulated in PLGA 50:50 or 75:25 microparticles (0.5%–2% w/w). Cumulative release was measured by UV–Vis spectrophotometry. Degree of conversion (DC) was analyzed by Fourier transform infrared spectroscopy; flexural strength and elastic modulus (E) were tested in three‐point bending; and water sorption (WS) and solubility (SL) were evaluated following ISO standards ( n = 10). Microtensile bond strength (TBS) was tested after 24 h, 6, and 12 months. Data were analyzed by anova with significance set at p < 0.05. PLGA 50:50/EGCG at 1% showed the highest release, reaching 77.30 µg. No significant differences were found in DC, E, WS, and SL among the groups. Bond strengths remained stable in all experimental groups after 6 and 12 months, except for the control. Incorporating 1% EGCG‐loaded PLGA 50:50 microparticles into Single Bond 2 may represent a promising strategy for controlled release without compromising physicochemical or mechanical properties.
Subjects
MeSH terms (MEDLINE)
Author keywords
Substances
Authors and institutions
- Graduate School of Dentistry, University Center Christus, Fortaleza, Ceará, Brazil.
- Graduate Program in Dentistry, Faculty of Pharmacy, Dentistry and Nursing, Federal University of Ceará, Fortaleza, Ceará, Brazil.
- School of Dentistry, University of Fortaleza, Fortaleza, Ceará, Brazil.
- Department of Biomedical Sciences & Comprehensive Care, Indiana University School of Dentistry, Indianapolis, Indiana, USA.
- Department of Pharmaceutical Sciences, Federal University of Amapá, Macapá, Amapá, Brazil.
ORCID profiles: Jiovanne Rabelo Neri, Nadine Luisa Guimarães Albuquerque, Marcelo Victor Sidou Lemos, Monica Yamauti, Francisco Fábio Oliveira de Sousa, Vanara Florêncio Passos, Sérgio Lima Santiago
Funding
- Conselho Nacional de Desenvolvimento Científico e Tecnológico
Cite
APA
Neri, J. R., Albuquerque, N. L. G., Lemos, M. V. S., Yamauti, M., de Sousa, F. F. O., Passos, V. F., & Santiago, S. L. (2026). Physicochemical characterization of etch‐and‐rinse adhesive system doped with catechin‐loaded polymeric microparticles. European Journal of Oral Sciences, 134(3). https://doi.org/10.1111/eos.70087
Vancouver
Neri JR, Albuquerque NLG, Lemos MVS, Yamauti M, de Sousa FFO, Passos VF, et al. Physicochemical characterization of etch‐and‐rinse adhesive system doped with catechin‐loaded polymeric microparticles. European Journal of Oral Sciences. 2026;134(3). doi:10.1111/eos.70087
BibTeX
@article{Neri2026,
author = {Neri, Jiovanne Rabelo and Albuquerque, Nadine Luisa Guimarães and Lemos, Marcelo Victor Sidou and Yamauti, Monica and de Sousa, Francisco Fábio Oliveira and Passos, Vanara Florêncio and Santiago, Sérgio Lima},
title = {Physicochemical characterization of etch‐and‐rinse adhesive system doped with catechin‐loaded polymeric microparticles},
journal = {European Journal of Oral Sciences},
year = {2026},
volume = {134},
number = {3},
doi = {10.1111/eos.70087}
}
EUVIMED