EUVIMEDOpdag EUVIMED
Crossref

Effect of thickness and aging on key mechanical properties of 3D‐printed crowns

Pei-Wen Peng iD, Chiao-Yun Peng iD, Jia-Syuan Chou iD, Le-Xin Chen iD, Chun-Wei Chao iD, Hidekazu Takahashi iD, Wei-Fang Lee iD

European Journal of Oral Sciences · 2026-02 · 134 (1)

DOI: 10.1111/eos.70048 ↗

At a glance

Journal article in European Journal of Oral Sciences, published online on 2025-11-02. Written by Pei-Wen Peng and 6 co-authors. Institution: School of Dental Technology, Taipei Medical University, Taipei, Taiwan. Major MEDLINE topics: Crowns, Printing, Three-Dimensional, Dental Prosthesis Design. Cited 5 times so far (Crossref); 36 references.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

With the growing demand for additively manufactured resin restorations, this study investigated the effects of cleaning time and thermal aging on key mechanical properties of digital light processing (DLP)‐fabricated resins for permanent crowns, and assessed how crown thickness (1.25, 1.50, 1.75, and 2.0 mm) influences fracture load. Specimens were ultrasonically cleaned in isopropanol for 180, 210, and 240 s and post‐cured for 30 min, and either stored in water (37°C, 24 h) or aged for 10,000 thermal cycles (5–55°C). Vickers hardness, flexural strength, shear bond strength, fracture load, and fit were assessed. Cleaning time affected only Vickers hardness, while thermal aging resulted in significantly degraded mechanical properties. Fracture load increased with thickness but decreased after aging, from 1240.3 ± 261.4 N to 955.3 ± 145.3 N for 2.0 mm crowns. Marginal gaps ranged from 54.09 to 79.43 µm, and internal gaps from 46.62 to 101.55 µm, and both decreased after aging. Crown thickness and thermal aging significantly impacted mechanical properties, whereas cleaning time had minimal impact. For durability and resistance to maximum clenching forces, a 2 mm thickness is recommended. These findings offer valuable insights into optimal post‐processing and design to enhance the clinical longevity of DLP‐fabricated crowns.

Subjects

MeSH terms (MEDLINE)

CrownsPrinting, Three-DimensionalDental Prosthesis DesignMaterials TestingHardnessHumansDental Stress AnalysisTime FactorsFlexural StrengthShear Strength

Author keywords

additive manufacturingbuild orientationsdigital light processingpermanent crownpost‐washing time

Authors and institutions

  • School of Dental Technology, Taipei Medical University, Taipei, Taiwan.
  • Department of Dentistry, Shin Kong Wu Ho-Su Memorial Hospital, Taipei, Taiwan.
  • Departamento de Odontología, Universidad CEU Cardenal Herrera, Moncada, Spain.
  • Department of Basic Oral Health Engineering, Institute of Science Tokyo (Science Tokyo), Tokyo, Japan.

ORCID profiles: Pei-Wen Peng, Chiao-Yun Peng, Jia-Syuan Chou, Le-Xin Chen, Chun-Wei Chao, Hidekazu Takahashi, Wei-Fang Lee

Cite

APA

Peng, P. W., Peng, C. Y., Chou, J. S., Chen, L. X., Chao, C. W., Takahashi, H., & Lee, W. F. (2026). Effect of thickness and aging on key mechanical properties of 3D‐printed crowns. European Journal of Oral Sciences, 134(1). https://doi.org/10.1111/eos.70048

Vancouver

Peng PW, Peng CY, Chou JS, Chen LX, Chao CW, Takahashi H, et al. Effect of thickness and aging on key mechanical properties of 3D‐printed crowns. European Journal of Oral Sciences. 2026;134(1). doi:10.1111/eos.70048

BibTeX
@article{Peng2026,
  author = {Peng, Pei-Wen and Peng, Chiao-Yun and Chou, Jia-Syuan and Chen, Le-Xin and Chao, Chun-Wei and Takahashi, Hidekazu and Lee, Wei-Fang},
  title = {Effect of thickness and aging on key mechanical properties of 3D‐printed crowns},
  journal = {European Journal of Oral Sciences},
  year = {2026},
  volume = {134},
  number = {1},
  doi = {10.1111/eos.70048}
}
Start for free →