EUVIMEDObjevte EUVIMED
Open access · CC BY 4.0

Load‐bearing capacity and wear characteristics of short fiber‐reinforced composite and glass ceramic fixed partial dentures

Enas Mangoush iD, Sufyan Garoushi iD, Pekka Vallittu iD, Lippo Lassila iD

European Journal of Oral Sciences · 2023

DOI: 10.1111/eos.12951 ↗

At a glance

Journal article in European Journal of Oral Sciences, 2023. Written by Enas Mangoush and 3 co-authors. Institution: Department of Biomaterials Science and Turku Clinical Biomaterial Center -TCBC, Institute of Dentistry, University of Turku, Turku, Finland. Major MEDLINE topics: Lithium, Ceramics. Cited 5 times so far (Crossref); 46 references. The full text is freely available (open access, CC BY 4.0).

AbstraktSubjectsBibliografické údajeCiteRelated studies

Abstract (original language)

The aim of this study was to evaluate load‐bearing capacity and wear performance of experimental short fiber‐reinforced composite (SFRC) and conventional lithium‐disilicate CAD/CAM fabricated fixed partial dentures (FPDs). Two groups ( n = 12/group) of three‐unit CAD/CAM fabricated posterior FPDs were made. The first group used experimental SFRC blocks, and the second group fabricated from lithium‐disilicate (IPS e.max CAD). All FPDs were luted on a zirconia testing jig with dual‐curing resin cement. Half of FPDs per group were quasi‐statically loaded until fracture. The other half experienced cyclic fatigue aging (100.000 cycles, Fmax = 500 N) before loading quasi‐statically until fracture. Fracture mode was examined using SEM. Wear test was performed using 15,000 loading cycles. Both material type and aging had a significant effect on the load‐bearing capacity of FPDs. Experimental SFRC CAD without fatigue aging had significantly the highest load‐bearing capacity (2096 ± 149N). Cyclic fatigue aging decreased the load‐bearing capacity of the SFRC group (1709 ± 188N) but increased it for the lithium‐disilicate group (1546 ± 155N). Wear depth values of SFRC CAD (29.3μm) were significantly lower compared to lithium‐disilicate (54.2μm). Experimental SFRC CAD demonstrated the highest load‐bearing capacity before and after cyclic fatigue aging, and superior wear behavior compared to the control material.

Subjects

MeSH terms (MEDLINE)

LithiumCeramicsDental PorcelainWeight-BearingComputer-Aided DesignDenture, Partial, FixedMaterials TestingDental Stress AnalysisDental Restoration Failure

Author keywords

CAD/CAM restorationabrasive wearfatigue agingfracture loadteeth supported fixed prosthesis

Substances

Glass ceramicsLithiumDental Porcelain

Authors and institutions

  • Department of Biomaterials Science and Turku Clinical Biomaterial Center -TCBC, Institute of Dentistry, University of Turku, Turku, Finland.
  • Wellbeing Services County of South-West Finland, Turku, Finland.

ORCID profiles: Enas Mangoush, Sufyan Garoushi, Pekka Vallittu, Lippo Lassila

Cite

APA

Mangoush, E., Garoushi, S., Vallittu, P., & Lassila, L. (2023). Load‐bearing capacity and wear characteristics of short fiber‐reinforced composite and glass ceramic fixed partial dentures. European Journal of Oral Sciences. https://doi.org/10.1111/eos.12951

Vancouver

Mangoush E, Garoushi S, Vallittu P, Lassila L. Load‐bearing capacity and wear characteristics of short fiber‐reinforced composite and glass ceramic fixed partial dentures. European Journal of Oral Sciences. 2023. doi:10.1111/eos.12951

BibTeX
@article{Mangoush2023,
  author = {Mangoush, Enas and Garoushi, Sufyan and Vallittu, Pekka and Lassila, Lippo},
  title = {Load‐bearing capacity and wear characteristics of short fiber‐reinforced composite and glass ceramic fixed partial dentures},
  journal = {European Journal of Oral Sciences},
  year = {2023},
  doi = {10.1111/eos.12951}
}
Start for free →