EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Simulated Self‐Assessment and Error Correction in Preclinical Prosthodontics: Insights From 3D‐Printed Models

Constance Cuny iD, Abhishek Kumar iD, Alexandre Thuries, Geromine Fournier, Coralie Bataille, Cathy Nabet iD, Antoine Galibourg iD

European Journal of Dental Education · 2026-05 · 30 (2) · 407-417

DOI: 10.1111/eje.13131 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Dental Education, online erschienen am 23.05.2025. Verfasst von Constance Cuny und 6 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Health, Department of Odontology, Oral Rehabilitation, Toulouse, France. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Education, Dental, Self-Assessment, Prosthodontics. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Developing self‐assessment and defect correction skills is essential for dental students to ensure high‐quality clinical practice. However, these skills are often insufficiently addressed in dental education. This study evaluates students' ability to assess and correct crown preparation defects through a structured exercise simulating self‐assessment using standardised 3D‐printed models with deliberate flaws. Additionally, it examines their improvement during the correction phase and their satisfaction with this innovative approach. Materials and Methods Students evaluated crown preparation defects on standardised 3D‐printed models, guided by a rubric‐based evaluation table, and subsequently corrected these defects using rotary instruments. Their perceptions of the exercise were captured through a satisfaction questionnaire.

Results

92% of students overestimated the presence or severity of defects during self‐assessment, with axial and occlusal reduction being the most challenging criteria. After the correction phase, students demonstrated significant improvement, particularly in axial reduction, although challenges persisted in occlusal reduction and finishing. Students expressed high satisfaction with the exercises, emphasising their value in enhancing learning and critical thinking.

Conclusion

This study underscores the importance of structured self‐assessment and correction exercises in dental education. By bridging the gap between self‐assessment and self‐correction, particularly in crown preparations, 3D‐printed models foster the development of clinical skills and autonomy amongst students.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalEducation, DentalSelf-AssessmentProsthodonticsModels, DentalHumansStudents, DentalClinical CompetenceSurveys and Questionnaires

Stichwörter der Autor:innen

3D printingerror correctionfixed prosthodonticspedagogyself‐assessment

Autor:innen und Institutionen

  • Faculty of Health, Department of Odontology, Oral Rehabilitation, Toulouse, France.
  • Division of Oral Rehabilitation, Department of Dental Medicine, Karolinska Institutet, Huddinge, Sweden.
  • Academic Center for Geriatric Dentistry, Stockholm, Sweden.
  • CNRS, Centre for Anthropobiology and Genomics of Toulouse, UMR 5288, Université Paul Sabatier, Toulouse, France.
  • INSERM UMR1295, Center for Epidemiology and Research in POPulation Health (CERPOP), Paris, France.

ORCID-Profile: Constance Cuny, Abhishek Kumar, Cathy Nabet, Antoine Galibourg

Zitieren

APA

Cuny, C., Kumar, A., Thuries, A., Fournier, G., Bataille, C., Nabet, C., & Galibourg, A. (2026). Simulated Self‐Assessment and Error Correction in Preclinical Prosthodontics: Insights From 3D‐Printed Models. European Journal of Dental Education, 30(2), 407-417. https://doi.org/10.1111/eje.13131

Vancouver

Cuny C, Kumar A, Thuries A, Fournier G, Bataille C, Nabet C, et al. Simulated Self‐Assessment and Error Correction in Preclinical Prosthodontics: Insights From 3D‐Printed Models. European Journal of Dental Education. 2026;30(2):407-417. doi:10.1111/eje.13131

BibTeX
@article{Cuny2026,
  author = {Cuny, Constance and Kumar, Abhishek and Thuries, Alexandre and Fournier, Geromine and Bataille, Coralie and Nabet, Cathy and Galibourg, Antoine},
  title = {Simulated Self‐Assessment and Error Correction in Preclinical Prosthodontics: Insights From 3D‐Printed Models},
  journal = {European Journal of Dental Education},
  year = {2026},
  volume = {30},
  number = {2},
  pages = {407--417},
  doi = {10.1111/eje.13131}
}
Kostenlos starten →