Effects of Access Cavity Design on the Shaping Ability and Dentine Thickness Following Canal Preparation Using XP ‐Endo Shaper or Reciproc
Australian Endodontic Journal · 2026
DOI: 10.1111/aej.70045 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift Australian Endodontic Journal, 2026. Verfasst von Renata Muniz Alvez Cruz und 6 weiteren Autor:innen. Beteiligte Einrichtung: Departament of Endodontics, State University of Rio de Janeiro, Rio de Janeiro, Brazil. Hauptthemen laut MEDLINE: Dentin, Root Canal Preparation, Dental Pulp Cavity. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Conselho Nacional de Desenvolvimento Científico e Tecnológico, Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.
Abstract (Originalsprache)
This study compared the shaping ability and remaining dentine thickness in mandibular molars prepared with traditional (TradAC) or ultraconservative (UltraAC) access cavities using Reciproc or XP‐endo Shaper instruments. Thirty‐two molars were scanned with micro‐CT before and after preparation to assess canal surface, volume, untouched walls, and dentine thickness. Both access cavity designs showed a significant reduction in dentine thickness after preparation, but no differences were found between TradAC and UltraAC in either mesial or distal roots ( p > 0.05). In the distal root, Reciproc produced a greater reduction in dentine thickness compared with XP‐endo Shaper ( p < 0.05), whereas shaping ability parameters did not differ significantly between instruments ( p > 0.05). Some canals exhibited residual dentine thickness below 0.5 mm, particularly when preoperative thickness was already minimal. Within the limitations of this laboratory study, access cavity design had no influence on dentine preservation, while the choice of instrument affected dentine reduction only in the distal root.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Departament of Endodontics, State University of Rio de Janeiro, Rio de Janeiro, Brazil.
- Department of Dentistry, Federal University of Juiz de Fora, Governador Valadares, Brazil.
- Nuclear Engineering Program, Federal University of Rio de Janeiro (UFRJ), Rio de Janeiro, Brazil.
- Oral Health Center, Brazilian Military Police, Minas Gerais, Brazil.
- Department of Endodontics, School of Dentistry, Grande Rio University (UNIGRANRIO), Rio de Janeiro, Brazil.
ORCID-Profile: Ana Flávia Almeida Barbosa, Emmanuel João Nogueira Leal da Silva, Luciana Moura Sassone
Förderung
- Conselho Nacional de Desenvolvimento Científico e Tecnológico
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Zitieren
APA
Cruz, R. M. A., Barbosa, A. F. A., de Lima, C. O., Lopes, R. T., Versiani, M. A., da Silva, E. J. N. L., & Sassone, L. M. (2026). Effects of Access Cavity Design on the Shaping Ability and Dentine Thickness Following Canal Preparation Using XP ‐Endo Shaper or Reciproc. Australian Endodontic Journal. https://doi.org/10.1111/aej.70045
Vancouver
Cruz RMA, Barbosa AFA, de Lima CO, Lopes RT, Versiani MA, da Silva EJNL, et al. Effects of Access Cavity Design on the Shaping Ability and Dentine Thickness Following Canal Preparation Using XP ‐Endo Shaper or Reciproc. Australian Endodontic Journal. 2026. doi:10.1111/aej.70045
BibTeX
@article{Cruz2026,
author = {Cruz, Renata Muniz Alvez and Barbosa, Ana Flávia Almeida and de Lima, Carolina Oliveira and Lopes, Ricardo Tadeu and Versiani, Marco Aurélio and da Silva, Emmanuel João Nogueira Leal and Sassone, Luciana Moura},
title = {Effects of Access Cavity Design on the Shaping Ability and Dentine Thickness Following Canal Preparation Using XP ‐Endo Shaper or Reciproc},
journal = {Australian Endodontic Journal},
year = {2026},
doi = {10.1111/aej.70045}
}
EUVIMED