EUVIMEDEUVIMED entdecken
Vergleichsstudie

Mechanical properties evaluation of two resin‐based three‐dimensional printing materials and dentine for endodontic training model fabrication: In vitro study

Anond Amornrattanavej, Kallaya Yanpiset iD, Jeeraphat Jantarat iD

Australian Endodontic Journal · 2024

DOI: 10.1111/aej.12827 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift Australian Endodontic Journal, 2024. Verfasst von Anond Amornrattanavej und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Operative Dentistry and Endodontics, Faculty of Dentistry, Mahidol University, Bangkok, Thailand. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Dentin, Materials Testing. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 30 Literaturangaben. Gefördert von: Pre-Seed Fund, Mahidol University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The objective of the study was to compare 4 mechanical properties of two 3‐D printing resins with dentine. Four mechanical tests were performed on dentine specimens, VeroClear resin and Splint resin with 15 samples each. Vickers hardness test, samples were subjected to a 300‐g load for 10 s. Flexural strength test, 8‐millimetre, beam‐shaped specimens were tested using the three‐point bending method. Drilling force was measured on flat‐surface specimens. Intra‐canal torque was measured on specimens imitating root canals. The results were analysed using the Kruskal–Wallis and Mann–Whitney tests with adjusted Bonferroni's p ‐value ( p < 0.05). Dentine exhibited the highest mechanical properties in all the tests. VeroClear's flexural strength and drilling force were higher, while the surface hardness was lower than that of Splint resin. The intra‐canal torque of dentine and VeroClear resin were not significant and higher than that of Splint resin. VeroClear's mechanical properties were closer to dentine than Splint resin.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalDentinMaterials TestingHumansIn Vitro TechniquesEndodonticsHardnessDental Stress AnalysisResins, SyntheticTorque

Stichwörter der Autor:innen

drilling forceendodontic training modelflexural strengthintra‐canal torquesurface micro‐hardnessthree‐dimensional printing resin polymer

Substanzen

Resins, Synthetic

Autor:innen und Institutionen

  • Department of Operative Dentistry and Endodontics, Faculty of Dentistry, Mahidol University, Bangkok, Thailand.

ORCID-Profile: Kallaya Yanpiset, Jeeraphat Jantarat

Förderung

  • Pre-Seed Fund, Mahidol University

Zitieren

APA

Amornrattanavej, A., Yanpiset, K., & Jantarat, J. (2024). Mechanical properties evaluation of two resin‐based three‐dimensional printing materials and dentine for endodontic training model fabrication: In vitro study. Australian Endodontic Journal. https://doi.org/10.1111/aej.12827

Vancouver

Amornrattanavej A, Yanpiset K, Jantarat J. Mechanical properties evaluation of two resin‐based three‐dimensional printing materials and dentine for endodontic training model fabrication: In vitro study. Australian Endodontic Journal. 2024. doi:10.1111/aej.12827

BibTeX
@article{Amornrattanavej2024,
  author = {Amornrattanavej, Anond and Yanpiset, Kallaya and Jantarat, Jeeraphat},
  title = {Mechanical properties evaluation of two resin‐based three‐dimensional printing materials and dentine for endodontic training model fabrication: In vitro study},
  journal = {Australian Endodontic Journal},
  year = {2024},
  doi = {10.1111/aej.12827}
}
Kostenlos starten →