Beam-Steerable Fabry–Perot Cavity Antenna With Mechanically Tunable Partially Reflective Surfaces for 6G Applications
IEEE Open Journal of Antennas and Propagation · 2026-08 · 7 (4) · 1232-1243
DOI: 10.1109/ojap.2026.3689395 ↗Kurz gefasst
Fachartikel in der Zeitschrift IEEE Open Journal of Antennas and Propagation, 2026-08. Verfasst von Edoardo Giusti und 3 weiteren Autor:innen. Die Arbeit nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Italian Ministry of Research (MUR) in the Framework of the Future-Oriented Research Laboratory of the Department of Information Engineering (DII), University o…, Piano Nazionale di Ripresa e Resilienza (Mission 4 (Education and Research), Component 2—High Performance Computing (M4C2â”HPC)), Big Data and Quantum Computing, SPOKE 6 Multiscale Modelling and Engineering Applications.
Abstract (Originalsprache)
A Fabry-Perot cavity antenna with beam steering capability enabled by the movement of a Partially Reflective Surface (PRS) is presented. Fabry-Perot cavities are commonly used due to their attractive properties, especially high gain and low profile. However, this configuration also presents design challenges when deployed for beam steering. Typically, beam steering is achieved by incorporating varactors into the metasurface unit-cells to locally modify the phase response with a controlled slope, which significantly complicates the implementation due to the feeding network introduction. To address this issue, the proposed solution involves designing the cavity in such a way that beam steering is achieved solely by moving the passive Partially Reflective Surface (PRS) along the cavity height direction. However, this approach leads to an increase in the Side Lobe Level (SLL) values, which worsens with progressively larger beam angles. To overcome the drawback, an aperiodic version of the PRS is opportunely introduced. By comparing the radiation patterns of the cavity equipped with the classical periodic metasurface against the aperiodic design, both gain preservation and SLL values reduction can be accomplished. Through accurate numerical simulations and experimental measurements acquired on fabricated prototypes, it emerges that the use of an aperiodic metasurface results in a SLL reduction ranging from 7.66 dB to 3 dB while maintaining the same gain level. The reduction in SLL up to 40° of beam tilting angle makes this antenna a suitable candidate for future 6G applications, in which beam scanning plays a critical role.
Förderung
- Italian Ministry of Research (MUR) in the Framework of the Future-Oriented Research Laboratory of the Department of Information Engineering (DII), University o…
- Piano Nazionale di Ripresa e Resilienza (Mission 4 (Education and Research), Component 2—High Performance Computing (M4C2â”HPC)), Big Data and Quantum Computing
- SPOKE 6 Multiscale Modelling and Engineering Applications
Zitieren
APA
Giusti, E., Usai, P., Brizi, D., & Monorchio, A. (2026). Beam-Steerable Fabry–Perot Cavity Antenna With Mechanically Tunable Partially Reflective Surfaces for 6G Applications. IEEE Open Journal of Antennas and Propagation, 7(4), 1232-1243. https://doi.org/10.1109/ojap.2026.3689395
Vancouver
Giusti E, Usai P, Brizi D, Monorchio A. Beam-Steerable Fabry–Perot Cavity Antenna With Mechanically Tunable Partially Reflective Surfaces for 6G Applications. IEEE Open Journal of Antennas and Propagation. 2026;7(4):1232-1243. doi:10.1109/ojap.2026.3689395
BibTeX
@article{Giusti2026,
author = {Giusti, Edoardo and Usai, Pierpaolo and Brizi, Danilo and Monorchio, Agostino},
title = {Beam-Steerable Fabry–Perot Cavity Antenna With Mechanically Tunable Partially Reflective Surfaces for 6G Applications},
journal = {IEEE Open Journal of Antennas and Propagation},
year = {2026},
volume = {7},
number = {4},
pages = {1232--1243},
doi = {10.1109/ojap.2026.3689395}
}
EUVIMED