EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Ionic release and electrochemical testing of 3-D printed orthodontics metallic bands made of Co-Cr and stainless-steel alloys

Spiros Zinelis iD, Aikaterini Sakellari iD, Sotirios Karavoltsos iD, Georgios Polychronis, Nearchos Panayi iD, Spyridon N Papageorgiou iD, Theodore Eliades iD

European Journal of Orthodontics · 12.06.2025 · 47 (4)

DOI: 10.1093/ejo/cjaf050 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Orthodontics, online erschienen am 05.07.2025. Verfasst von Spiros Zinelis und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomaterials, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece. Hauptthemen laut MEDLINE: Stainless Steel, Chromium Alloys, Printing, Three-Dimensional, Dental Alloys. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

The aim of this study was to investigate the electrochemical characteristics and ionic release of three-dimensional (3D) printed orthodontic metallic bands made of stainless-steel (SS) and Cobalt-Chromium (Co-Cr) alloys. Materials and Methods Thirty-six orthodontic metallic bands were prepared by 3D printing, employing SS (n = 18) and Co-Cr (n = 18) alloys. The ionic release from each alloy was determined according to ISO 27020:2019 requirements employing flame atomic absorption spectrometry (FAAS). The electrochemical properties were characterized by Open Circuit Potential (OCP), Anodic Scan (AS) and Electrochemical Impedance Spectroscopy (EIS). In all cases a 0.1M NaCl, 0.1 M lactic acid solution was used. The EIS data were fitted to a Randles circuit and the sum of ionic release of probed elements after immersion along with OCP, zero corrosion potential (Ecorr), corrosion current density (Icorr), and pitting corrosion potential (Epit) were compared with t-tests/Mann-Whitney tests (α = 0.05).

Results

SS bands showed an approximately 44-fold higher total ionic release compared to Co-Cr ones. Electrochemical testing revealed no statistically significant differences for Ecorr but Co-Cr illustrated more beneficial OCP, Icorr and Epit values than SS. Both alloys illustrated semicircles in Nyquist plots, implying that the electrochemical process was under charge transfer control, while the equivalent circuit simulation showed a higher charge transfer resistance for Co-Cr alloy (SS:14191.1 vs Co-Cr:33158.7 Ωcm2), implying lower corrosion current and thus decreased corrosion rate.

Conclusion

Immersion and electrochemical testing indicated that Co-Cr alloys showed increased corrosion resistance over SS ones, which might affect efficacy under clinical use.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Stainless SteelChromium AlloysPrinting, Three-DimensionalDental AlloysOrthodontic WiresMaterials TestingCorrosionDielectric SpectroscopyElectrochemical TechniquesIonsCobaltSpectrophotometry, Atomic

Stichwörter der Autor:innen

3D printingCo-Cr alloyscorrosionorthodontic bandsstainless steel alloys

Substanzen

Stainless SteelChromium AlloysDental AlloysIonsCobalt

Autor:innen und Institutionen

  • Department of Biomaterials, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece.
  • Laboratory of Environmental Chemistry, Department of Chemistry, National and Kapodistrian University of Athens, Athens, Greece.
  • Department of Dentistry, European University Cyprus, Nicosia, Cyprus.
  • Clinic of Orthodontics and Pediatric Dentistry, Center for Dental Medicine, University of Zurich, Switzerland.

ORCID-Profile: Spiros Zinelis, Aikaterini Sakellari, Sotirios Karavoltsos, Nearchos Panayi, Spyridon N Papageorgiou, Theodore Eliades

Zitieren

APA

Zinelis, S., Sakellari, A., Karavoltsos, S., Polychronis, G., Panayi, N., Papageorgiou, S. N., & Eliades, T. (2025). Ionic release and electrochemical testing of 3-D printed orthodontics metallic bands made of Co-Cr and stainless-steel alloys. European Journal of Orthodontics, 47(4). https://doi.org/10.1093/ejo/cjaf050

Vancouver

Zinelis S, Sakellari A, Karavoltsos S, Polychronis G, Panayi N, Papageorgiou SN, et al. Ionic release and electrochemical testing of 3-D printed orthodontics metallic bands made of Co-Cr and stainless-steel alloys. European Journal of Orthodontics. 2025;47(4). doi:10.1093/ejo/cjaf050

BibTeX
@article{Zinelis2025,
  author = {Zinelis, Spiros and Sakellari, Aikaterini and Karavoltsos, Sotirios and Polychronis, Georgios and Panayi, Nearchos and Papageorgiou, Spyridon N and Eliades, Theodore},
  title = {Ionic release and electrochemical testing of 3-D printed orthodontics metallic bands made of Co-Cr and stainless-steel alloys},
  journal = {European Journal of Orthodontics},
  year = {2025},
  volume = {47},
  number = {4},
  doi = {10.1093/ejo/cjaf050}
}
Kostenlos starten →