EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of heat treatment and nitrogen atmosphere during post-curing on mechanical properties of 3D-printed orthodontic aligners

Mélanie Mattle, Spiros Zinelis iD, Georgios Polychronis, Olga Makou, Nearchos Panayi iD, Spyridon N Papageorgiou iD, Theodore Eliades iD

European Journal of Orthodontics · 01.01.2024 · 46 (1)

DOI: 10.1093/ejo/cjad074 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Orthodontics, online erschienen am 11.12.2023. Verfasst von Mélanie Mattle und 6 weiteren Autor:innen. Beteiligte Einrichtung: Clinic of Orthodontics and Pediatric Dentistry, Center of Dental Medicine, University of Zurich, Zurich, Switzerland. Hauptthemen laut MEDLINE: Hot Temperature, Tooth. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: University of Zurich.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

Three-dimensional (3D)-printed aligners present a promising orthodontic treatment modality, whose clinical success largely depends on the material’s mechanical properties. The aim of this study was to evaluate the mechanical properties of resin-made 3D-printed aligners and assess the effect of two different post-curing conditions. Materials and methods Forty dumbbell-shaped specimens and 40 resin aligners were 3D-printed and divided into four equal groups according to post-curing conditions: presence or absence of oxygen during post-curing and water heat treatment at 85°C for 15 s or none. Samples from the central incisor of the aligner (n = 5/group) were studied by Attenuated Total Reflection Fourier-transform infrared spectroscopy (ATR-FTIR). The dumbbell-shaped specimens were loaded up to fracture under tensile mode and yield strength, ultimate tensile strength, elastic and plastic strain were calculated. The first mandibular molar area from 3D-printed aligners (n = 10/group) was cut and embedded in acrylic resin and then underwent metallographic grinding and polishing followed by instrumented indentation testing to determine the following mechanical properties: Martens hardness, indentation modulus, elastic index, and indentation relaxation. After descriptive statistics, differences according to each post-curing protocol, as well as their combination, were analyzed with linear regression modeling at a 5% significance level.

Results

All groups showed identical ATR-FTIR spectra, while no statistically significant effects were seen for either post-curing protocol (N2 presence and heat treatment) or their combination (P > .05 in all instances).

Conclusions

The mechanical properties of 3D-printed resin aligners were not considerably affected either by post-curing in N2 atmosphere or heat treatment.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Hot TemperatureToothHumansHardnessPrinting, Three-DimensionalMaterials TestingSurface Properties

Stichwörter der Autor:innen

3D printingFTIRalignersinstrumented indentation testingmechanical propertiesorthodontic

Autor:innen und Institutionen

  • Clinic of Orthodontics and Pediatric Dentistry, Center of Dental Medicine, University of Zurich, Zurich, Switzerland.
  • Department of Biomaterials, School of Dentistry, National and Kapodistrian University of Athens, Athens, Greece.
  • Department of Dentistry, European University Cyprus, Nicosia, Cyprus.

ORCID-Profile: Spiros Zinelis, Nearchos Panayi, Spyridon N Papageorgiou, Theodore Eliades

Förderung

  • University of Zurich

Zitieren

APA

Mattle, M., Zinelis, S., Polychronis, G., Makou, O., Panayi, N., Papageorgiou, S. N., & Eliades, T. (2024). Effect of heat treatment and nitrogen atmosphere during post-curing on mechanical properties of 3D-printed orthodontic aligners. European Journal of Orthodontics, 46(1). https://doi.org/10.1093/ejo/cjad074

Vancouver

Mattle M, Zinelis S, Polychronis G, Makou O, Panayi N, Papageorgiou SN, et al. Effect of heat treatment and nitrogen atmosphere during post-curing on mechanical properties of 3D-printed orthodontic aligners. European Journal of Orthodontics. 2024;46(1). doi:10.1093/ejo/cjad074

BibTeX
@article{Mattle2024,
  author = {Mattle, Mélanie and Zinelis, Spiros and Polychronis, Georgios and Makou, Olga and Panayi, Nearchos and Papageorgiou, Spyridon N and Eliades, Theodore},
  title = {Effect of heat treatment and nitrogen atmosphere during post-curing on mechanical properties of 3D-printed orthodontic aligners},
  journal = {European Journal of Orthodontics},
  year = {2024},
  volume = {46},
  number = {1},
  doi = {10.1093/ejo/cjad074}
}
Kostenlos starten →