Bridging the Gap in Rhinoplasty Training: The Effectiveness of 3D Printed Models in Surgical Education
Aesthetic Surgery Journal · 16.06.2025 · 45 (7) · 655-661
DOI: 10.1093/asj/sjaf045 ↗Kurz gefasst
Validierungsstudie in der Zeitschrift Aesthetic Surgery Journal, online erschienen am 25.03.2025. Verfasst von Umar Rehman und 8 weiteren Autor:innen. Hauptthemen laut MEDLINE: Rhinoplasty, Printing, Three-Dimensional, Models, Anatomic. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Background
Rhinoplasty is a common facial plastic surgery procedure for both functional and aesthetic indications. The use of 3-dimensional (3D) models has been reported as a potential method for providing hands-on training for learning rhinoplasty without jeopardizing patient care.
Objectives
The objective of this study was to develop and validate a novel model for rhinoplasty training.
Methods
The rhinoplasty models were designed and produced with proprietary 3D printing technology. Face and content validity were assessed during a rhinoplasty course involving 53 surgeons. Criterion validity was evaluated in a training session with 20 surgical residents, measuring improvements in surgical skills after practice with the 3D models, with an objective structured assessment of technical skills (OSAT).
Results
All surgeons (n = 53, 100%) stated that the rhinoplasty model aided in their learning and development. In all, 91% (n = 48) of surgeons rated the realism of the model as excellent or very good in comparison to cadaveric specimens. Assessment of criterion validity showed a statistically significant improvement in OSAT scores among surgical residents, increasing from a baseline of 11.7/40 (SD ± 1.80) to 21.6/40 (SD ± 1.79) post session (P < .0001).
Conclusions
The 3D rhinoplasty models showed good content, face, and criterion validity, objectively improving residents’ surgical performance. Rhinoplasty 3D models may serve as a precadaveric training adjunct, equipping trainees with fundamental skills before cadaveric dissection, or as a primary training modality in countries with limited cadaver access. Therefore the models offer an innovative approach to training the next generation of rhinoplasty surgeons.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Autor:innen und Institutionen
ORCID-Profile: David Kahn
Zitieren
APA
Rehman, U., Polglase, N., Kahn, D., Dogan, T., Paun, S., D'Souza, A., Uppal, R., Eynon-Lewis, N., & Lechner, M. (2025). Bridging the Gap in Rhinoplasty Training: The Effectiveness of 3D Printed Models in Surgical Education. Aesthetic Surgery Journal, 45(7), 655-661. https://doi.org/10.1093/asj/sjaf045
Vancouver
Rehman U, Polglase N, Kahn D, Dogan T, Paun S, D'Souza A, et al. Bridging the Gap in Rhinoplasty Training: The Effectiveness of 3D Printed Models in Surgical Education. Aesthetic Surgery Journal. 2025;45(7):655-661. doi:10.1093/asj/sjaf045
BibTeX
@article{Rehman2025,
author = {Rehman, Umar and Polglase, Natasha and Kahn, David and Dogan, Teoman and Paun, Santdeep and D'Souza, Alwyn and Uppal, Rajan and Eynon-Lewis, Nicholas and Lechner, Matt},
title = {Bridging the Gap in Rhinoplasty Training: The Effectiveness of 3D Printed Models in Surgical Education},
journal = {Aesthetic Surgery Journal},
year = {2025},
volume = {45},
number = {7},
pages = {655--661},
doi = {10.1093/asj/sjaf045}
}
EUVIMED