EUVIMEDEUVIMED entdecken
Open Access

Investigation of In Situ Vibration During Wire and Arc Additive Manufacturing

Chi Ma, Changlong Li, Yuhao Yan, Yonghong Liu iD, Xinlei Wu iD, Dege Li, Hui Jin, Fan Zhang

3D Printing and Additive Manufacturing · 2023-06 · 10 (3) · 524-535

DOI: 10.1089/3dp.2021.0053 ↗

Kurz gefasst

Fachartikel in der Zeitschrift 3D Printing and Additive Manufacturing, online erschienen am 08.06.2023. Verfasst von Chi Ma und 7 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical and Electronic Engineering, China University of Petroleum (East China), Qingdao, China. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Wire and arc additive manufacturing (WAAM) is becoming a promising technique due to its high deposition rate and low cost. However, WAAM faces challenges of coarse grains. In this study, a novel in situ vibration method was proposed to suppress these imperfections of WAAM. Temperature and vibration distributions were explored first, and the optimized parameters were utilized for manufacturing low-carbon steel parts. The results revealed that after the vibration, the average grain size in fine grain zone was reduced from 9.8 to 7.1 μm, and that in coarse grain zone was declined from 10.6 to 7.4 μm, respectively. No large deformation occurred due to the low temperature. Grain refining was attributed to more dendrite fragments induced by excessive stress at the roots of dendrites. The refined grains enhanced mechanical strength of the parts in both X and Z directions and improved the average hardness. After the vibration, the ultimate tensile strength and yield strength were increased to 522.5 and 395 MPa, which represented an increase of 10% and 13.8%, respectively. The average hardness was improved to 163 HV, which was an increase of 10.1%.

Schlagwörter

Stichwörter der Autor:innen

grain refiningin situ vibrationwire and arc additive manufacturing

Autor:innen und Institutionen

  • College of Mechanical and Electronic Engineering, China University of Petroleum (East China), Qingdao, China.

ORCID-Profile: Yonghong Liu, Xinlei Wu

Zitieren

APA

Ma, C., Li, C., Yan, Y., Liu, Y., Wu, X., Li, D., Jin, H., & Zhang, F. (2023). Investigation of In Situ Vibration During Wire and Arc Additive Manufacturing. 3D Printing and Additive Manufacturing, 10(3), 524-535. https://doi.org/10.1089/3dp.2021.0053

Vancouver

Ma C, Li C, Yan Y, Liu Y, Wu X, Li D, et al. Investigation of In Situ Vibration During Wire and Arc Additive Manufacturing. 3D Printing and Additive Manufacturing. 2023;10(3):524-535. doi:10.1089/3dp.2021.0053

BibTeX
@article{Ma2023,
  author = {Ma, Chi and Li, Changlong and Yan, Yuhao and Liu, Yonghong and Wu, Xinlei and Li, Dege and Jin, Hui and Zhang, Fan},
  title = {Investigation of In Situ Vibration During Wire and Arc Additive Manufacturing},
  journal = {3D Printing and Additive Manufacturing},
  year = {2023},
  volume = {10},
  number = {3},
  pages = {524--535},
  doi = {10.1089/3dp.2021.0053}
}
Kostenlos starten →