EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multistable kirigami soft grippers with sustainable magnetic actuation and conformal 3D/4D printing

Moslem Mohammadi iD, Eui-Hyun Kim iD, Keun Park iD, Ali Zolfagharian iD

Bioinspiration & Biomimetics · 31.12.2026 · 21 (6) · 066005

DOI: 10.1088/1748-3190/aeb77c ↗

Kurz gefasst

Fachartikel in der Zeitschrift Bioinspiration & Biomimetics, online erschienen am 11.11.2026. Verfasst von Moslem Mohammadi und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Engineering, Deakin University, Geelong, Victoria 3216, Australia. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Robotics, Biomimetics. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Seoul National University of Science and Technology, Australian Research Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Soft robotic grippers are well suited to handling delicate and irregular objects, yet many remain difficult to deploy in practice due to high hardware overhead (pumps, valves, motors) and continuous energy demand during grasping. This study presents a sustainable multi-stable soft gripper that decouples activation from holding and reduces manufacturing waste through mandrel-based, support-free multi-material fused filament fabrication. The gripper is a thin-walled cylindrical shell patterned with a circumferential auxetic kirigami lattice composed of bistable unit cells. Sequential snap-through transitions among the graded cell groups give rise to multistable behaviour at the gripper level, while the fully closed and fully deployed states serve as the functional grasping and object-acquisition states, respectively. A magnetically responsive distal tip, allows non-contact triggering to switch the structure into an expanded, truncated-cone open state for object acquisition, followed by snap-back to the closed state for passive grasping. Mechanical characterizations quantified activation and holding performance for two gripper sizes (36 mm and 58 mm initial diameters). The small gripper, with 25 g weight and up to 48 payload-to-weight ratios, reliably activated across pulling speeds from 10 to 1385 mm·min −1 , showing repeatable multi-peak snap-through behaviour and consistent activation displacement of ∼20 mm, with peak activation forces of approximately 10–12 N under six-magnet loading. Object pull-out tests demonstrated stable passive holding, with maximum pull-out forces ranging from ∼3–5 N for 40–48 mm circular objects (small gripper) and up to ∼17 N for non-circular objects (large gripper), with higher forces often arising from passive geometric interlocking. Finite element simulations using a Mooney–Rivlin hyperelastic thermoplastic elastomer model reproduced the snap-through sequence and instability locations, supporting interpretation of the activation mechanics. Robotic demonstrations on a 3-DoF arm further validated practical pick-and-place capability without onboard actuators or sensors for food industry and agricultural products.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalRoboticsBiomimeticsEquipment Design

Stichwörter der Autor:innen

3D/4D printingadditive manufacturingkirigamimagnetic actuationsoft gripper

Autor:innen und Institutionen

  • School of Engineering, Deakin University, Geelong, Victoria 3216, Australia.
  • Department of Mechanical Design and Robot Engineering, Seoul National University of Science and Technology, Seoul, Republic of Korea.

ORCID-Profile: Moslem Mohammadi, Eui-Hyun Kim, Keun Park, Ali Zolfagharian

Förderung

  • Seoul National University of Science and Technology
  • Australian Research Council

Zitieren

APA

Mohammadi, M., Kim, E. H., Park, K., & Zolfagharian, A. (2026). Multistable kirigami soft grippers with sustainable magnetic actuation and conformal 3D/4D printing. Bioinspiration & Biomimetics, 21(6), 066005. https://doi.org/10.1088/1748-3190/aeb77c

Vancouver

Mohammadi M, Kim EH, Park K, Zolfagharian A. Multistable kirigami soft grippers with sustainable magnetic actuation and conformal 3D/4D printing. Bioinspiration & Biomimetics. 2026;21(6):066005. doi:10.1088/1748-3190/aeb77c

BibTeX
@article{Mohammadi2026,
  author = {Mohammadi, Moslem and Kim, Eui-Hyun and Park, Keun and Zolfagharian, Ali},
  title = {Multistable kirigami soft grippers with sustainable magnetic actuation and conformal 3D/4D printing},
  journal = {Bioinspiration & Biomimetics},
  year = {2026},
  volume = {21},
  number = {6},
  pages = {066005},
  doi = {10.1088/1748-3190/aeb77c}
}
Kostenlos starten →