Finite element modeling and experimental validation of radial shear rolling of bioresorbable Fe–30Mn–5Si alloy
Modelling and Simulation in Materials Science and Engineering · 31.07.2026 · 34 (5) · 055021
DOI: 10.1088/1361-651x/ae8564 ↗Kurz gefasst
Fachartikel in der Zeitschrift Modelling and Simulation in Materials Science and Engineering, online erschienen am 23.07.2026. Verfasst von Pulat Kadirov und 6 weiteren Autor:innen. Die Arbeit nennt 38 Literaturangaben. Gefördert von: Russian Science Foundation.
Abstract (Originalsprache)
In this study, finite element modeling (FEM) of radial shear rolling (RSR) at 900 °C for a bioresorbable Fe–30Mn–5Si alloy was developed and experimentally validated. The strain rate distribution across the cross-section was nonuniform and strongly dependent on the drawing ratio, with maximal values in the peripheral zones, primarily at the workpiece-roll interface. The stress-strain state was characterized by predominantly compressive stresses in the peripheral zone, transitioning to tensile stresses toward the center, where stress triaxiality reached slightly positive values. Equivalent strain was higher in the peripheral zone than in the central one. FEM-simulated temperature distribution during the RSR revealed significant heating in the peripheral zone (from ∼40 °C to ∼100 °C), which promoted softening processes and minimized the microstructure gradient across the cross-section. Based on these findings, defect-free long-length semi-products with a final diameter of 20 mm were produced via RSR in six passes. Optical microscopy revealed microstructural evolution during RSR, showing formation of an equiaxed, statically recrystallized structure with average grain sizes of 9 ± 2 μ m in the peripheral zone and 15 ± 3 μ m in the central zone under the developed conditions. X-ray diffraction analysis revealed that the RSR produces a two-phase state consisting predominantly of FCC γ -austenite, with trace amounts of HCP cooling-induced ϵ -martensite present in both the peripheral and central zones. The resulting microstructure increased microhardness to ∼275 HV in the peripheral zone and ∼265 HV in the central one. These findings demonstrate the effectiveness of FEM analysis for RSR of the bioresorbable Fe–30Mn–5Si alloy. Thus, the FEM-simulated RSR parameters derived for a chosen strain rate and deformation temperature (the stress-strain state, stress triaxiality, and equivalent strain distributions) enable the production of high-quality, defect-free, long-length semi-products.
Förderung
- Russian Science Foundation
Zitieren
APA
Kadirov, P., Khakimova, A., Zhukova, Y., Sadykova, Y., Sheremetyev, V., Strakhov, O., & Prokoshkin, S. (2026). Finite element modeling and experimental validation of radial shear rolling of bioresorbable Fe–30Mn–5Si alloy. Modelling and Simulation in Materials Science and Engineering, 34(5), 055021. https://doi.org/10.1088/1361-651x/ae8564
Vancouver
Kadirov P, Khakimova A, Zhukova Y, Sadykova Y, Sheremetyev V, Strakhov O, et al. Finite element modeling and experimental validation of radial shear rolling of bioresorbable Fe–30Mn–5Si alloy. Modelling and Simulation in Materials Science and Engineering. 2026;34(5):055021. doi:10.1088/1361-651x/ae8564
BibTeX
@article{Kadirov2026,
author = {Kadirov, Pulat and Khakimova, Anna and Zhukova, Yulia and Sadykova, Yulia and Sheremetyev, Vadim and Strakhov, Oleg and Prokoshkin, Sergey},
title = {Finite element modeling and experimental validation of radial shear rolling of bioresorbable Fe–30Mn–5Si alloy},
journal = {Modelling and Simulation in Materials Science and Engineering},
year = {2026},
volume = {34},
number = {5},
pages = {055021},
doi = {10.1088/1361-651x/ae8564}
}
EUVIMED