EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading

Z. A. Roberts, A. M. Schmalzer, C. B. Brown, J. P. Lichthardt, J. D. Yeager, B. C. Tappan, A. H. Mueller

Journal of Applied Physics · 14.08.2025 · 138 (6)

DOI: 10.1063/5.0281480 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Applied Physics, online erschienen am 08.08.2025. Verfasst von Z. A. Roberts und 6 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Los Alamos National Laboratory.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The performance of a high explosive charge is highly influenced by the detonation velocity and any inherent internal structure. Additively manufactured (AM) high explosive charges allow for a precisely engineered internal structure and the selective placement of discrete or graded volumes of a tailored material, which are unachievable by conventional means. The dilution of a solid explosive by an inert additive for detonation velocity reduction is herein evaluated for a method of material extrusion called a direct-ink-write AM, where an 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane-based ultraviolet -curable energetic-binder paste explosive was diluted by the inert density mock 5-iodo-2′-deoxyuridine for use in the manufacture of multi-material explosive charges. The explosive ink was characterized for printing by rheological and particle size measurements, and the detonation velocities for 0–40 wt. % inert diluent were found to have a continuous linear reduction in detonation velocity down to 14.3% difference. A two-component 3D plane wave explosive lens with 8.038 km/s “fast” and 7.491 km/s “slow” diluted ink in an internal cone demonstrated a reduced time of breakout at the output face from 361 to 53 ns. A linearly graded “fast–slow–fast” cylinder was successfully printed and fired, showing engineered control along the length of the charge as the detonation velocity dropped from 7.851 to 6.700 km/s and then recovered to 7.241 km/s. The extreme control over the internal composition of a high explosive charge via a dual-material extruder/mixer challenges conventional manufacturing approaches and opens new avenues for engineered detonation wavefronts, high explosive charge performance, and new applications.

Förderung

  • Los Alamos National Laboratory

Zitieren

APA

Roberts, Z. A., Schmalzer, A. M., Brown, C. B., Lichthardt, J. P., Yeager, J. D., Tappan, B. C., & Mueller, A. H. (2025). Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading. Journal of Applied Physics, 138(6). https://doi.org/10.1063/5.0281480

Vancouver

Roberts ZA, Schmalzer AM, Brown CB, Lichthardt JP, Yeager JD, Tappan BC, et al. Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading. Journal of Applied Physics. 2025;138(6). doi:10.1063/5.0281480

BibTeX
@article{Roberts2025,
  author = {Roberts, Z. A. and Schmalzer, A. M. and Brown, C. B. and Lichthardt, J. P. and Yeager, J. D. and Tappan, B. C. and Mueller, A. H.},
  title = {Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading},
  journal = {Journal of Applied Physics},
  year = {2025},
  volume = {138},
  number = {6},
  doi = {10.1063/5.0281480}
}
Kostenlos starten →