EUVIMEDEUVIMED entdecken
Crossref

Impact of ladle plug clogging on multiphase flow and refining efficiency in ladle furnace

Ning Wang, Zhongqiu Liu, Yuchao Yao, Yongtao Xiong, Yu Li, Baokuan Li

Physics of Fluids · 01.06.2025 · 37 (6)

DOI: 10.1063/5.0269672 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Physics of Fluids, online erschienen am 26.06.2025. Verfasst von Ning Wang und 5 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 47 Literaturangaben. Gefördert von: Excellent Younth Fund of liaoning Natural Science Foundation, Liaoning Xingliao Talents-Top-notch Young Talents Project, National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ladle plug clogging, a widespread challenge in ladle refining, profoundly influences various stages of the process. However, existing numerical simulations and water model experiments primarily assume an idealized non-clogging condition, posing a significant constraint on the comprehensive understanding and optimization of refining operations. This study comprehensively investigates the impact of porous plugs on refining efficiency under various clogging conditions, with a focus on gas–liquid flow, mixing time, and slag eye behavior to establish a full-size three-dimensional mathematical model of 135 t ladle and offers practical solutions to mitigate the negative effects. A 1:4 water model experiments were carried out to verify the accuracy of mathematical models. The results indicate that plug clogging influences refining efficiency by altering the initial bubble characteristics. As the degree of clogging increases, the initial bubble diameter distribution shifts toward larger diameters. The overall stirring energy is reduced by approximate 10%, and the axial velocity in the slag-molten steel interface and bubble plume area is significantly reduced. At flow rates of 300 and 450 NL/min, mixing time exhibits a positive correlation with the degree of clogging. However, when the flow rate increases to 600 NL/min, mixing time fluctuates unpredictably with clogging severity. When the initial flow rates are 300 and 450 NL/min, following clogging, increasing the flow rate to 600 NL/min may offset the negative impact of congestion on mixing time. Post-clogging, the slag eye area decreases by up to 18%, and the instability in slag eye fluctuation increases with higher clogging severity. This mathematical model can also be employed to investigate the clogging issues of slot-type plugs.

Förderung

  • Excellent Younth Fund of liaoning Natural Science Foundation
  • Liaoning Xingliao Talents-Top-notch Young Talents Project
  • National Natural Science Foundation of China

Zitieren

APA

Wang, N., Liu, Z., Yao, Y., Xiong, Y., Li, Y., & Li, B. (2025). Impact of ladle plug clogging on multiphase flow and refining efficiency in ladle furnace. Physics of Fluids, 37(6). https://doi.org/10.1063/5.0269672

Vancouver

Wang N, Liu Z, Yao Y, Xiong Y, Li Y, Li B. Impact of ladle plug clogging on multiphase flow and refining efficiency in ladle furnace. Physics of Fluids. 2025;37(6). doi:10.1063/5.0269672

BibTeX
@article{Wang2025,
  author = {Wang, Ning and Liu, Zhongqiu and Yao, Yuchao and Xiong, Yongtao and Li, Yu and Li, Baokuan},
  title = {Impact of ladle plug clogging on multiphase flow and refining efficiency in ladle furnace},
  journal = {Physics of Fluids},
  year = {2025},
  volume = {37},
  number = {6},
  doi = {10.1063/5.0269672}
}
Kostenlos starten →