Experimental and numerical analysis on the cutting force, cutting temperature, and tool wear of alloy steel (4340) during turning process
AIP Advances · 01.11.2024 · 14 (11)
DOI: 10.1063/5.0227710 ↗Kurz gefasst
Fachartikel in der Zeitschrift AIP Advances, online erschienen am 21.11.2024. Verfasst von G. Veerappan und 8 weiteren Autor:innen. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: King Saud University.
Abstract (Originalsprache)
This paper focuses primarily on the wear behavior observed in AISI4340 steel when machining with a multi-layered coated carbide tool. Numerical and experimental examination is processed out to predict the wear performance of AISI 4340 steel along with its cutting force and temperature. In this process, four layers of different coated material are bonded together to form a multi-layered coated carbide tool. The coated thickness is assessed with the assistance of a Scanning Electron Microscope (SEM). Experimental analysis takes place with a heavy duty lathe machine equipped with an infrared thermometer and force dynamometer. Simulation is performed using DEFORM-2D software to simulate cutting forces and interface temperature, and the output results obtained have been compared with the experimental work. With the help of the SEM image, maximum crater wear depth is evaluated and analyzed. Feed plays a crucial role in increasing the chip interface temperature and cutting force. For varied feed rates, the cutting tool edge radius, depth of cut, and cutting speed are taken as the input parameters. The proposed 2D finite element model provides effective parameter values for reducing wear. Results measured indicate that the output parameter values of interface temperature and cutting force obtained from simulation and experimental investigation match each other with high accuracy. Simulation results for temperature distribution around the tool tip show that a maximum temperature of 654 °C is formed at the feed rate of 0.4 mm/rev, leading to high heat flux. For the feed rate of 0.3 and 0.2 mm/rev, there is not much deviation in heat flux around the tool tip. The maximum temperature around the tool tip is near 527 °C for both 0.3 and 0.2 mm/rev. Simulation results show that the lowest tool wear of 0.001 23 mm was obtained for a feed rate of 0.2 mm/rev, followed by 0.004 25 (0.1 mm/rev), 0.005 09 mm (0.4 mm/rev), and 0.007 14 mm/rev.
Förderung
- King Saud University
Zitieren
APA
Veerappan, G., Logesh, K., Chaturvedi, R., Ravichandran, M., Mohanavel, V., Hossain, I., Kannan, S., Alotaibi, M. A., & Seikh, A. H. (2024). Experimental and numerical analysis on the cutting force, cutting temperature, and tool wear of alloy steel (4340) during turning process. AIP Advances, 14(11). https://doi.org/10.1063/5.0227710
Vancouver
Veerappan G, Logesh K, Chaturvedi R, Ravichandran M, Mohanavel V, Hossain I, et al. Experimental and numerical analysis on the cutting force, cutting temperature, and tool wear of alloy steel (4340) during turning process. AIP Advances. 2024;14(11). doi:10.1063/5.0227710
BibTeX
@article{Veerappan2024,
author = {Veerappan, G. and Logesh, Kamaraj and Chaturvedi, Rishabh and Ravichandran, Manickam and Mohanavel, Vinayagam and Hossain, Ismail and Kannan, Sathish and Alotaibi, Majed A. and Seikh, Asiful H.},
title = {Experimental and numerical analysis on the cutting force, cutting temperature, and tool wear of alloy steel (4340) during turning process},
journal = {AIP Advances},
year = {2024},
volume = {14},
number = {11},
doi = {10.1063/5.0227710}
}
EUVIMED