Color Characteristics of High Yttrium Oxide–Doped Monochrome and Multilayer Partially Stabilized Zirconia upon Different Sintering Parameters
European Journal of Dentistry · 01.02.2025 · 19 (01) · 227-239
DOI: 10.1055/s-0044-1787700 ↗Kurz gefasst
Fachartikel in der Zeitschrift European Journal of Dentistry, erschienen am 01.02.2025. Verfasst von Niwut Juntavee und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Khon Kaen University, Khon Kaen, Thailand. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Royal Thai Government.
Abstract (Originalsprache)
Objectives
Sintering influences the optical properties of zirconia. This study examined the effect of altering sintering temperature and time of monochrome (Mo) and multilayer (Mu) 5 mol% yttria-partially stabilized zirconia (5Y-PSZ) on color characteristics. Materials and Methods Three hundred specimens (width × length × thickness = 10 × 20 × 2 mm) were prepared from Mo and Mu (with cervical [C], middle [M], and incisal [I] region) 5Y-PSZ and randomly sintered at decreasing (Td: 1,450°C), regular (Tr: 1,500°C), and increasing (TI: 1,550°C) sintering temperature, with extremely short (He: 10 minutes), ultrashort (Hu: 15 minutes), short (Hs: 30 minutes), and regular (Hr: 135 minutes) sintering time (n = 15/group). Color appearance (EW ), translucency parameter (TP), contrast ratio (CR), opalescence parameter (OP), and color appearance difference (∆E diff) were evaluated in the CIE L*a*b* system. Microstructures were evaluated by scanning electron microscope (SEM) and X-ray diffractometer (XRD). Statistical Analysis Analysis of variance (ANOVA) and Bonferroni comparisons were determined for significant differences (p < 0.05).
Results
Significant differences in color parameters upon zirconia type, sintering temperature, and sintering time, and their interactions were indicated (p < 0.05). Increasing sintering temperature and extended sintered time resulted in larger grain, reduced tetragonal-to-monoclinic phase transformation, and significantly increased the TP and OP, but decreased the CR and ∆E diff (p < 0.05). Decreasing sintering temperature and time led to clinically unacceptable color appearance.
Conclusion
Mo was found to be more translucent than Mu. To achieve the most favorable optical properties, increasing sintering temperature and extending sintering time are recommended. Decreasing sintering temperature is not suggested. However, shortened sintering time is feasible, but it needs sintering with increasing sintering temperature to achieve a promising color appearance.
Autor:innen und Institutionen
- Department of Prosthodontics, Faculty of Dentistry, Khon Kaen University, Khon Kaen, Thailand.
- Department of Preventive Dentistry, Division of Pediatric Dentistry, Faculty of Dentistry, Khon Kaen University, Khon Kaen, Thailand.
- Division of Biomaterials and Prosthodontics Research, Faculty of Dentistry, Khon Kaen University, Khon Kaen, Thailand.
ORCID-Profile: Niwut Juntavee, Apa Juntavee
Förderung
- Royal Thai Government
Zitieren
APA
Juntavee, N., Juntavee, A., & Jaralpong, C. (2025). Color Characteristics of High Yttrium Oxide–Doped Monochrome and Multilayer Partially Stabilized Zirconia upon Different Sintering Parameters. European Journal of Dentistry, 19(01), 227-239. https://doi.org/10.1055/s-0044-1787700
Vancouver
Juntavee N, Juntavee A, Jaralpong C. Color Characteristics of High Yttrium Oxide–Doped Monochrome and Multilayer Partially Stabilized Zirconia upon Different Sintering Parameters. European Journal of Dentistry. 2025;19(01):227-239. doi:10.1055/s-0044-1787700
BibTeX
@article{Juntavee2025,
author = {Juntavee, Niwut and Juntavee, Apa and Jaralpong, Chutikarn},
title = {Color Characteristics of High Yttrium Oxide–Doped Monochrome and Multilayer Partially Stabilized Zirconia upon Different Sintering Parameters},
journal = {European Journal of Dentistry},
year = {2025},
volume = {19},
number = {01},
pages = {227--239},
doi = {10.1055/s-0044-1787700}
}
EUVIMED