EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Instrumented Puncture Test of High-Density Polyethylene: Identification of Critical Displacement Points and Effects of Puncture Rate and Sample Thickness

Ruxin Zang, Quanxiao Dong, Yubao Guo, Zhiyong Jiang iD, Yongfeng Men iD

Polymer Science & Technology · 27.10.2026 · 2 (10) · 786-797

DOI: 10.1021/polymscitech.6c00045 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Science & Technology, online erschienen am 04.05.2026. Verfasst von Ruxin Zang und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Applied Chemistry and Engineering, University of Science and Technology of China, Hefei 230026, P. R. China. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Natural Science Foundation of China, Jilin Province Science and Technology Development Plan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Instrumented puncture tests were performed on high-density polyethylene (HDPE) sheets using a flat-ended indenter and a clamped specimen holder. By correlating in situ morphology with puncture force–displacement curves, a consistent set of characteristic displacements was identified for a range of samples with different thicknesses. DC marks the critical displacement where a bending-to-stretching transition, accompanied by stress concentration, drawing of the crown wall, and the onset of microfibrillation, sets in. DD corresponds to the displacement where the maximum force within the fibrillation-dominated regime is reached. A puncture step-cycle test protocol separated recoverable and residual displacements, quantitatively validating the inferred elastoplastic sequence. Based on an energy partition at DC, the critical energy (UC), total absorbed energy (Utotal), and plastic dissipation energy (UP) were determined, and a puncture-specific ductile ratio (D.R.p) was proposed to quantify ductile energy dissipation. Under the present experimental conditions, systematic variations in puncture rate (2–800 mm/min) and specimen thickness (0.47–2.63 mm) reveal two critical thresholds: a transition from quasi-static to rate-dominated response at approximately 80 mm/min and a plate-like to film-like mechanism boundary at approximately 1.2 mm. These results establish a physical framework for mechanistic interpretation and ductility quantification in the puncture behavior of polymers.

Schlagwörter

Stichwörter der Autor:innen

HDPE puncture mechanicsductile-to-rate transitionelastoplastic deformationenergy partitioningforce-displacement behavior

Autor:innen und Institutionen

  • School of Applied Chemistry and Engineering, University of Science and Technology of China, Hefei 230026, P. R. China.
  • State Key Laboratory of Polymer Science and Technology, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China.
  • Railway Engineering Research Institute, China Academy of Railway Sciences Corporation Limited, Beijing 100081, P.R. China.
  • Hebei Tieke Yichen New Materials Technology Co., Ltd., Shijiazhuang 052160, P. R. China.

ORCID-Profile: Zhiyong Jiang, Yongfeng Men

Förderung

  • National Natural Science Foundation of China
  • Jilin Province Science and Technology Development Plan

Zitieren

APA

Zang, R., Dong, Q., Guo, Y., Jiang, Z., & Men, Y. (2026). Instrumented Puncture Test of High-Density Polyethylene: Identification of Critical Displacement Points and Effects of Puncture Rate and Sample Thickness. Polymer Science & Technology, 2(10), 786-797. https://doi.org/10.1021/polymscitech.6c00045

Vancouver

Zang R, Dong Q, Guo Y, Jiang Z, Men Y. Instrumented Puncture Test of High-Density Polyethylene: Identification of Critical Displacement Points and Effects of Puncture Rate and Sample Thickness. Polymer Science & Technology. 2026;2(10):786-797. doi:10.1021/polymscitech.6c00045

BibTeX
@article{Zang2026,
  author = {Zang, Ruxin and Dong, Quanxiao and Guo, Yubao and Jiang, Zhiyong and Men, Yongfeng},
  title = {Instrumented Puncture Test of High-Density Polyethylene: Identification of Critical Displacement Points and Effects of Puncture Rate and Sample Thickness},
  journal = {Polymer Science & Technology},
  year = {2026},
  volume = {2},
  number = {10},
  pages = {786--797},
  doi = {10.1021/polymscitech.6c00045}
}
Kostenlos starten →