EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Microfibrillated Cellulose as a Reinforcement Agent in Acrylonitrile Styrene Acrylate (ASA) for MEX 3D Printing: A Thermomechanical and Rheological Filler Content Assessment

Nectarios Vidakis, Emmanuel Stratakis, Nikolaos Michailidis, Vassilis Papadakis, Nikolaos Mountakis, Maria Spyridaki, Aikaterini Gkagkanatsiou, Nektarios K. Nasikas, Markos Petousis

ACS Omega · 18.11.2026

DOI: 10.1021/acsomega.6c11290 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Omega, online erschienen am 18.11.2026. Verfasst von Nectarios Vidakis und 8 weiteren Autor:innen. Die Arbeit nennt 112 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, acrylonitrile styrene acrylate (ASA), a thermoplastic with great resistance to weather conditions, was combined with the nature-sourced microfibrillated cellulose (MFC) to produce composites with improved properties in additive manufacturing (AM). Filament extrusion was used to fabricate the filaments. The test specimens were 3D printed for thermal, rheological, dynamic mechanical, and mechanical characterization. The thermal behavior was assessed by thermogravimetric analysis and differential scanning calorimetry, while the rheological performance was evaluated through viscosity and material flow rate measurements. The effect of MFC on quality metrics (dimensional accuracy and porosity) was also assessed using microcomputed tomography. Among the five composites investigated (0.5–2.5 wt % MFC, step 0.5 wt %), the 1.5 wt % sample showed the best overall performance, except in Vickers microhardness. Compared with pure ASA, this composite improved tensile strength and toughness, flexural toughness, and Charpy impact strength by approximately 13%, tensile modulus by 15%, flexural modulus by 12%, and flexural strength by approximately 28%. The highest Vickers microhardness was achieved by the 1.0 wt % composite, showing a 30.8% increase over pure ASA. Overall, the introduction of the biobased MFC, even at low loadings, enhanced the mechanical strength of ASA and improved the quality metrics. Such findings highlight the potential of ASA/MFC as a sustainable composite for outdoor 3D printing applications.

Zitieren

APA

Vidakis, N., Stratakis, E., Michailidis, N., Papadakis, V., Mountakis, N., Spyridaki, M., Gkagkanatsiou, A., Nasikas, N. K., & Petousis, M. (2026). Microfibrillated Cellulose as a Reinforcement Agent in Acrylonitrile Styrene Acrylate (ASA) for MEX 3D Printing: A Thermomechanical and Rheological Filler Content Assessment. ACS Omega. https://doi.org/10.1021/acsomega.6c11290

Vancouver

Vidakis N, Stratakis E, Michailidis N, Papadakis V, Mountakis N, Spyridaki M, et al. Microfibrillated Cellulose as a Reinforcement Agent in Acrylonitrile Styrene Acrylate (ASA) for MEX 3D Printing: A Thermomechanical and Rheological Filler Content Assessment. ACS Omega. 2026. doi:10.1021/acsomega.6c11290

BibTeX
@article{Vidakis2026,
  author = {Vidakis, Nectarios and Stratakis, Emmanuel and Michailidis, Nikolaos and Papadakis, Vassilis and Mountakis, Nikolaos and Spyridaki, Maria and Gkagkanatsiou, Aikaterini and Nasikas, Nektarios K. and Petousis, Markos},
  title = {Microfibrillated Cellulose as a Reinforcement Agent in Acrylonitrile Styrene Acrylate (ASA) for MEX 3D Printing: A Thermomechanical and Rheological Filler Content Assessment},
  journal = {ACS Omega},
  year = {2026},
  doi = {10.1021/acsomega.6c11290}
}
Kostenlos starten →