EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Parametrically Engineered Laser-Induced Graphene with Tunable Electrical and Morphological Properties for Flexible Sensor Applications

Faizan Tariq Beigh iD, Nadeem Tariq Beigh, Dhiman Mallick iD

ACS Omega · 28.07.2026 · 11 (29) · 44087-44107

DOI: 10.1021/acsomega.6c03731 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Omega, online erschienen am 16.07.2026. Verfasst von Faizan Tariq Beigh und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Electrical Engineering, Indian Institute of Technology Delhi, Hauz Khas, New Delhi 110016, India. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 86 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Indian Council of Medical Research.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Laser-induced graphene (LIG) provides a scalable and maskless route for fabricating three-dimensional porous graphene on polymer substrates for flexible electronics. However, achieving reproducible control over its electrical and structural properties remains challenging due to the complex interplay of laser processing parameters. Here, we systematically investigate the effects of laser power, scan speed, dots per inch (DPI), energy per unit area (EPUA), and depth of focus (DOF) on the morphology, crystallinity, and conductivity of LIG formed on polyimide substrates. The optimized LIG exhibits excellent structural quality (ID/IG ∼ 0.25, La ∼ 76 nm) and low sheet resistance (∼10 Ω/□), within the lower range of reported values. The material is further validated through flexible piezoresistive sensors and electrothermal heaters. The pressure sensor demonstrates two distinct sensitivity regimes (1.25% N1– and 32% N1–), a low limit of detection (∼150 mN), and minimal hysteresis (∼5–6%). Piezoresistive behavior is governed by deformation-induced modulation of conductive pathways involving interflake contact resistance, tunneling effects, and microstructural rearrangement within the porous LIG network. The LIG-based microheater achieves a temperature of 201 °C within 6.2 s at a low operating voltage of 6.5 V, outperforming many reported flexible heaters in terms of heating efficiency. These results establish a transferable framework for engineering high-quality LIG with tunable properties and demonstrate its potential for scalable, low-power multifunctional flexible electronic applications.

Autor:innen und Institutionen

  • Department of Electrical Engineering, Indian Institute of Technology Delhi, Hauz Khas, New Delhi 110016, India.
  • Department of Mechanical and Nuclear Engineering, Khalifa University, Abu Dhabi 127788, UAE.

ORCID-Profile: Faizan Tariq Beigh, Dhiman Mallick

Förderung

  • Indian Council of Medical Research

Zitieren

APA

Beigh, F. T., Beigh, N. T., & Mallick, D. (2026). Parametrically Engineered Laser-Induced Graphene with Tunable Electrical and Morphological Properties for Flexible Sensor Applications. ACS Omega, 11(29), 44087-44107. https://doi.org/10.1021/acsomega.6c03731

Vancouver

Beigh FT, Beigh NT, Mallick D. Parametrically Engineered Laser-Induced Graphene with Tunable Electrical and Morphological Properties for Flexible Sensor Applications. ACS Omega. 2026;11(29):44087-44107. doi:10.1021/acsomega.6c03731

BibTeX
@article{Beigh2026,
  author = {Beigh, Faizan Tariq and Beigh, Nadeem Tariq and Mallick, Dhiman},
  title = {Parametrically Engineered Laser-Induced Graphene with Tunable Electrical and Morphological Properties for Flexible Sensor Applications},
  journal = {ACS Omega},
  year = {2026},
  volume = {11},
  number = {29},
  pages = {44087--44107},
  doi = {10.1021/acsomega.6c03731}
}
Kostenlos starten →