EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Environmentally Friendly Production of Graphene Oxide via Ball Milling: Characterization and Life Cycle Assessment

Suparat Sasrimuang, Chanawat Sirichat iD, Channarong Puchongkawarin iD, Oruethai Jaiboon, Santamon Luanwuthi iD

ACS Omega · 22.07.2025 · 10 (28) · 30896-30905

DOI: 10.1021/acsomega.5c03296 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Omega, online erschienen am 14.07.2025. Verfasst von Suparat Sasrimuang und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical Engineering, Faculty of Engineering, Ubon Ratchathani University, Ubon Ratchathani 34190, Thailand. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Thailand Science Research and Innovation, Ubon Ratchathani University, Research Group Grant from Faculty of Engineering, Ubon Ratchathani University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluates the environmental impact and structural evolution of graphene oxide (GO) produced via a sodium sulfate-assisted ball milling method, focusing on the effect of milling duration. Graphite was milled for 6, 12, 18, and 24 h, and the resulting GO samples were characterized using Raman spectroscopy, X-ray diffraction, and scanning electron microscopy to assess defect density, crystallite size, and flake morphology. The 12 h milling duration produced GO with optimal characteristics, including an ID/IG ratio of 1.00, an in-plane crystallite size (La) of 19.18 nm, and an average flake size of 1.22 ± 0.84 μm. Prolonged milling to 24 h increased the ID/IG ratio to 1.22, decreased La to 15.71 nm, and reduced the average flake size to 0.53 ± 0.23 μm, indicating higher defect density and material degradation. A cradle-to-gate life cycle assessment (LCA) was conducted to quantify the environmental footprint associated with each milling duration. The 12 h process demonstrated the lowest global warming potential (GWP) at 8.55 kg CO2-equivalent per kilogram of GO, with electricity consumption and sodium sulfate usage identified as the primary environmental impact contributors. Longer milling durations led to greater environmental burdens without corresponding material improvements. These results suggest that the 12 h milling condition strikes an optimal balance between product quality and environmental performance. This work supports sodium sulfate-assisted ball milling as a scalable and more sustainable alternative to traditional chemical oxidation methods for GO production.

Autor:innen und Institutionen

  • Department of Chemical Engineering, Faculty of Engineering, Ubon Ratchathani University, Ubon Ratchathani 34190, Thailand.
  • Department of Curriculum and Instruction, Faculty of Education, Mahasarakham University, Mahasarakham 44000, Thailand.
  • Department of Physics, Faculty of Science, Ubon Ratchathani University, Ubon Ratchathani 34190, Thailand.
  • Department of Industrial Engineering, Faculty of Engineering, Ubon Ratchathani University, Ubon Ratchathani 34190, Thailand.

ORCID-Profile: Chanawat Sirichat, Channarong Puchongkawarin, Santamon Luanwuthi

Förderung

  • Thailand Science Research and Innovation
  • Ubon Ratchathani University
  • Research Group Grant from Faculty of Engineering, Ubon Ratchathani University

Zitieren

APA

Sasrimuang, S., Sirichat, C., Puchongkawarin, C., Jaiboon, O., & Luanwuthi, S. (2025). Environmentally Friendly Production of Graphene Oxide via Ball Milling: Characterization and Life Cycle Assessment. ACS Omega, 10(28), 30896-30905. https://doi.org/10.1021/acsomega.5c03296

Vancouver

Sasrimuang S, Sirichat C, Puchongkawarin C, Jaiboon O, Luanwuthi S. Environmentally Friendly Production of Graphene Oxide via Ball Milling: Characterization and Life Cycle Assessment. ACS Omega. 2025;10(28):30896-30905. doi:10.1021/acsomega.5c03296

BibTeX
@article{Sasrimuang2025,
  author = {Sasrimuang, Suparat and Sirichat, Chanawat and Puchongkawarin, Channarong and Jaiboon, Oruethai and Luanwuthi, Santamon},
  title = {Environmentally Friendly Production of Graphene Oxide via Ball Milling: Characterization and Life Cycle Assessment},
  journal = {ACS Omega},
  year = {2025},
  volume = {10},
  number = {28},
  pages = {30896--30905},
  doi = {10.1021/acsomega.5c03296}
}
Kostenlos starten →